Influence of the parameters of the pre-stressed winding on the oscillations of vertical cylindrical steel oil tanks

Authors

DOI:

https://doi.org/10.15587/1729-4061.2022.265107

Keywords:

oil tank, tank oscillations, preliminary stresses, winding tension, numerical method

Abstract

This paper reports an analysis of the frequencies and shapes of oscillations of the tank with a volume of 3000 m3 with a winding of high-strength steel wire with a diameter of 3 mm, 4 mm, and 5 mm, applied in increments of 1:3. In addition, for the tension force of the turn in the range from 0.2 to 0.8 of the yield strength of the wire material. The study was carried out on the basis of a finite-element method in the ANSYS software package for a three-dimensional geometric model of the structure. At the same time, the software took into consideration the height-uneven width of the cylindrical wall taking into account the height of the filling to the maximum height and the tension forces of the winding.

It has been established that a change in the diameter of the winding wire does not lead to a significant change in the spectrum for the first ten significant frequencies. And an increase in the tension force of the wire in the winding leads to a decrease in the magnitude of oscillation frequencies. The exception is the sixth frequency. Its values are equal to one-tenth of a Hz for all estimated cases of the force of tension of the turn in the range from 0.2 to 0.8 of the yield strength of the wire material. The oscillation shapes of the tank reinforced by the winding have been determined. The change in the tension force of the wire in the winding does not change the number of waves at the circumferential coordinate at the free edge of the structure. We studied the loss of stability of the tank wall under distributed internal pressure. A comparative analysis of the sixth oscillation shape and the shape of stability loss reveals that they have the same number of waves at the circumferential coordinate.

The results reported here could make it possible to effectively use the pre-stress in order to detune the tank from the resonant frequency when operating in seismically hazardous areas

Author Biographies

Timur Tursunkululy, Mukhtar Auezov South Kazakhstan University

Doctoral Student

Department of Construction and Building Materials

Nurlan Zhangabay, Mukhtar Auezov South Kazakhstan University

PhD, Associate Professor

Department of Construction and Building Materials

Konstantin Avramov, A. Pidhornyi Institute of Mechanical Engineering Problems of the National Academy of Sciences of Ukraine

Doctor of Technical Sciences, Professor

Department of Reliability and Dynamic Strength

Maryna Chernobryvko, A. Pidhornyi Institute of Mechanical Engineering Problems of the National Academy of Sciences of Ukraine

Doctor of Technical Sciences

Department of Reliability and Dynamic Strength

Ulanbator Suleimenov, Mukhtar Auezov South Kazakhstan University

Doctor of Technical Sciences, Professor

Department of Architecture

Akmaral Utelbayeva, Mukhtar Auezov South Kazakhstan University

Doctor of Chemical Sciences, Associate Professor

Department of Chemistry

References

  1. Wang, Y., Su, J., Wang, K., Zhang, B., Zhao, J., Liu, X. (2012). Distribution and accumulation of global deep oil and gas. Natural Gas Geoscience, 23 (3), 526–534. Available at: https://www.semanticscholar.org/paper/d1125d4c165d947e2573a3a7add987ce0517973d
  2. Hud, M. (2022). Simulation of the stress-strain state of a cylindrical tank under the action of forced oscillations. Procedia Structural Integrity, 36, 79–86. doi: https://doi.org/10.1016/j.prostr.2022.01.006
  3. Tursunkululy, T., Zhangabay, N., Avramov, K., Chernobryvko, M., Suleimenov, U., Utelbayeva, A. et. al. (2022). Strength analysis of prestressed vertical cylindrical steel oil tanks under operational and dynamic loads. Eastern-European Journal of Enterprise Technologies, 2 (7 (116)), 14–21. doi: https://doi.org/10.15587/1729-4061.2022.254218
  4. Jaramillo, F., Almazán, J. L., Colombo, J. I. (2022). Effects of the anchor bolts and soil flexibility on the seismic response of cylindrical steel liquid storage tanks. Engineering Structures, 263, 114353. doi: https://doi.org/10.1016/j.engstruct.2022.114353
  5. Suleimenov, U., Zhangabay, N., Utelbayeva, A., Azmi Murad, M. A., Dosmakanbetova, A., Abshenov, K. et. al. (2022). Estimation of the strength of vertical cylindrical liquid storage tanks with dents in the wall. Eastern-European Journal of Enterprise Technologies, 1 (7 (115)), 6–20. doi: https://doi.org/10.15587/1729-4061.2022.252599
  6. Suleimenov, U., Zhangabay, N., Abshenov, K., Utelbayeva, A., Imanaliyev, K., Mussayeva, S. et. al. (2022). Estimating the stressed-strained state of the vertical mounting joint of the cylindrical tank wall taking into consideration imperfections. Eastern-European Journal of Enterprise Technologies, 3 (7 (117)), 14–21. doi: https://doi.org/10.15587/1729-4061.2022.258118
  7. Suleimenov, U., Zhangabay, N., Utelbayeva, A., Ibrahim, M. N. M., Moldagaliyev, A., Abshenov, K. et. al. (2021). Determining the features of oscillations in prestressed pipelines. Eastern-European Journal of Enterprise Technologies, 6 (7 (114)), 85–92. doi: https://doi.org/10.15587/1729-4061.2021.246751
  8. Yasniy, P. V., Mykhailyshyn, M. S., Pyndus, Yu. I., Hud, M. I. (2020). Numerical Analysis of Natural Vibrations of Cylindrical Shells Made of Aluminum Alloy. Materials Science, 55 (4), 502–508. doi: https://doi.org/10.1007/s11003-020-00331-2
  9. Kuś, J., Wałach, S. (2021). Analysis of steel tank shell deformation and its impact on further utilisation. International Journal of Pressure Vessels and Piping, 193, 104453. doi: https://doi.org/10.1016/j.ijpvp.2021.104453
  10. Avramov, K. V., Chernobryvko, M., Uspensky, B., Seitkazenova, K. K., Myrzaliyev, D. (2019). Self-sustained vibrations of functionally graded carbon nanotubes-reinforced composite cylindrical shells in supersonic flow. Nonlinear Dynamics, 98 (3), 1853–1876. doi: https://doi.org/10.1007/s11071-019-05292-z
  11. Avramov, K. V. (2006). Nonlinear forced vibrations of a cylindrical shell with two internal resonances. International Applied Mechanics, 42 (2), 169–175. doi: https://doi.org/10.1007/s10778-006-0072-5
  12. Avramov, K. V., Chernobryvko, M. V., Tonkonozhenko, A. M. (2018). Dynamics of solid propellant motor composite casing under impact pressure. Meccanica, 53 (13), 3339–3353. doi: https://doi.org/10.1007/s11012-018-0876-5
  13. Ghanbari Ghazijahani, T., Showkati, H. (2013). Experiments on cylindrical shells under pure bending and external pressure. Journal of Constructional Steel Research, 88, 109–122. doi: https://doi.org/10.1016/j.jcsr.2013.04.009
  14. Joniak, S., Magnucki, K., Szyc, W. (2011). Buckling Study of Steel Open Circular Cylindrical Shells in Pure Bending. Strain, 47 (3), 209–214. doi: https://doi.org/10.1111/j.1475-1305.2009.00669.x
  15. Al-Yacouby, A. M., Hao, L. J., Liew, M. S., Ratnayake, R. M. C., Samarakoon, S. M. K. (2021). Thin-Walled Cylindrical Shell Storage Tank under Blast Impacts: Finite Element Analysis. Materials, 14 (22), 7100. doi: https://doi.org/10.3390/ma14227100
  16. Wang, Z., Hu, K., Zhao, Y. (2022). Doom-roof steel tanks under external explosion: Dynamic responses and anti-explosion measures. Journal of Constructional Steel Research, 190, 107118. doi: https://doi.org/10.1016/j.jcsr.2021.107118
  17. Bragov, A., Konstantinov, A., Lomunov, A., Kruszka, L. (2021). Comparative analysis of dynamic strength and impact toughness of pipe steels. EPJ Web of Conferences, 250, 04002. doi: https://doi.org/10.1051/epjconf/202125004002
  18. Chernobryvko, M., Kruszka, L., Vorobiev, Y. (2014). Thermo-Elastic-Plastic Constitutive Model for Numerical Analysis of Metallic Structures under Local Impulsive Loadings. Applied Mechanics and Materials, 566, 493–498. doi: https://doi.org/10.4028/www.scientific.net/amm.566.493
  19. Ye, Z., Birk, A. M. (1994). Fluid Pressures in Partially Liquid-Filled Horizontal Cylindrical Vessels Undergoing Impact Acceleration. Journal of Pressure Vessel Technology, 116 (4), 449–458. doi: https://doi.org/10.1115/1.2929615
  20. Prokopov, A. Ju., Tkacheva, K. E. (2015). A study of stress-strain state of Foundation of vertical vessel subject to dynamic operating loads. Engineering Journal of Don, 3. Available at: http://www.ivdon.ru/en/magazine/archive/n3y2015/3200
  21. Zhangabay, N., Sapargaliyeva, B., Utelbayeva, A., Kolesnikov, A., Aldiyarov, Z., Dossybekov, S. et. al. (2022). Experimental Analysis of the Stress State of a Prestressed Cylindrical Shell with Various Structural Parameters. Materials, 15 (14), 4996. doi: https://doi.org/10.3390/ma15144996
  22. Aydın Korucuk, F. M., Maali, M., Kılıç, M., Aydın, A. C. (2019). Experimental analysis of the effect of dent variation on the buckling capacity of thin-walled cylindrical shells. Thin-Walled Structures, 143, 106259. doi: https://doi.org/10.1016/j.tws.2019.106259
  23. Maslak, M., Pazdanowski, M., Siudut, J., Tarsa, K. (2017). Corrosion Durability Estimation for Steel Shell of a Tank Used to Store Liquid Fuels. Procedia Engineering, 172, 723–730. doi: https://doi.org/10.1016/j.proeng.2017.02.092
  24. Śliwa, A., Kwaśny, W., Nabia k, M., Dziwis, R. (2019). Numerical Analysis of Static Tensile Test of the Sample Made of Polyethylene Reinforced by Halloysite Nanoparticles. Acta Physica Polonica A, 136 (6), 996–1000. doi: https://doi.org/10.12693/aphyspola.136.996
Influence of the parameters of the pre-stressed winding on the oscillations of vertical cylindrical steel oil tanks

Downloads

Published

2022-10-31

How to Cite

Tursunkululy, T., Zhangabay, N., Avramov, K., Chernobryvko, M., Suleimenov, U., & Utelbayeva, A. (2022). Influence of the parameters of the pre-stressed winding on the oscillations of vertical cylindrical steel oil tanks. Eastern-European Journal of Enterprise Technologies, 5(7 (119), 6–13. https://doi.org/10.15587/1729-4061.2022.265107

Issue

Vol. 5 No. 7 (119) (2022): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2022 Timur Tursunkululy, Nurlan Zhangabay, Konstantin Avramov, Maryna Chernobryvko, Ulanbator Suleimenov, Akmaral Utelbayeva

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.