Perfection of systems of cooling of shovels high-temperature power GTE

Authors

  • Ю.Я. Дашевский Отдел турбин ГП НПКГ «Зоря-Машпроект» г. Николаев, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2010.2754

Keywords:

film-cooling adiabatic effectiveness, blowing ratio, holes geometry.

Abstract

The present report gives an analytical survey of investigations, aimed, first of all, on increasing of film-cooling systems effectiveness for the turbine nozzle vanes and blades being used in modern advanced gas turbines for power generation. Advantages and disadvantages of the presented cooling techniques are also discussed.

Author Biography

Ю.Я. Дашевский, Отдел турбин ГП НПКГ «Зоря-Машпроект» г. Николаев

Начальник сектора тепловых и гидравлических расчетов

References

  1. Халатов А.А., Борисов И.И., Дашевский Ю.Я. “ Системы охлаждения лопаток современных ГТД ” – Восточно-Европейский журнал передовых технологий// 2009 - №4/4 - т.40, ISSN1729-3774.
  2. Халатов А.А., Романов В.В., Дашевский Ю.Я., Письменный Д.Н. “ Тенденции развития систем охлаждения лопаток высокотемпературных энергетических ГТД ” – Промышленная теплотехника // 2010 -№1,№2 - т.32, ISSN0204-3602.
  3. Lutum E., et al.,”Influence of the Hole Length-to diameter Ratio on Film Cooling with Cylindrical Holes”, ASME Paper 98-GT-10.
  4. Sgarzi O., et al “Analysis of Vortices in Three-Dimensional Jets Introduced in a Cross-Flow Boundary-Layer”, ASME Paper 97-GT-517.
  5. Brauckmann D., et al., “Application of Steady and Transient IR-thermography Measurements to Film Cooling Experiments for a Row of Shaped Holes”, ASME Paper GT2005-68035.
  6. Brauckmann D., et al., “Influence of Compound Angle on Adiabatic Film Cooling Effectiveness and Heat Transfer Coefficient for a Row of Shaped Film Cooling Holes”, ASME Paper GT2005-68036.
  7. Bohn D., et al., “Conjugate Heat Transfer Analysis for Film Cooling Configurations with Different Hole Geometries”, ASME Paper GT2003-38369.
  8. Saumweber C., et al., “Free-Stream Turbulence Effects on Film Cooling with Shaped Holes”, ASME Paper GT-2002-30170.
  9. Lu Y. et al., “Influence of Hole Angle on Leading Edge Showerhead Film Cooling”, ASME Paper GT2006-90370.
  10. Bunker R.S., “Film Cooling Effectiveness due to Discrete Holes within a Transverse Surface Slot”, ASME Paper GT2002-30178.
  11. Waye S.C. et al., “High Resolution Film Cooling Effectiveness Measurements of Axial Holes Embedded in a Transverse Trench with Various Trench Configuration”, ASME Paper GT2006-90226.
  12. Lu Y. et al., “Trench Film Cooling – Effect of Trench Downstream Edge and Hole Spacing”, ASME Paper GT2008-50606.
  13. Sundaram N. et al., “Film-Cooling Flowfields with Trenched Holes on an Endwall”, ASME Paper GT2008-50149.
  14. Kusterer K. et al., “Double-Jet Film-Cooling for Highly Efficient Film-Cooling with Low Blowing Ratios”, ASME Paper GT2008-50073.
  15. Kusterer K. et al., “A Parametric Study on the Influence of the Lateral Ejection Angle of Double-Jet Holes on the Film-Cooling Effectiveness for High Blowing Ratios”, ASME Paper GT2009-59321.
  16. Копелев С.З. “Охлаждаемые лопатки газовых турбин. Тепловой расчет и профилирование” М.: Наука, 1983, с.145.

Downloads

Published

2010-04-06

How to Cite

Дашевский, Ю. (2010). Perfection of systems of cooling of shovels high-temperature power GTE. Eastern-European Journal of Enterprise Technologies, 3(2(45), 24–31. https://doi.org/10.15587/1729-4061.2010.2754

Issue

Vol. 3 No. 2(45) (2010): Modern technologies in gas-turbine construction. Part I

Section

Modern technologies in the gas-turbine

License

Copyright (c) 2014 Ю.Я. Дашевский

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.