Diagnostics of processes of wear of materials of ball-tube mills
DOI:
https://doi.org/10.15587/1729-4061.2015.36638Keywords:
material hardness, tube mill ball structure, radiation diagnosticsAbstract
Changes in material hardness of balls, which are used as the working body of ball-tube mills was investigated. Both new balls and balls with different operation time were examined. Hardness of not only the surface layer, but also over the entire depth was studied. These measurements were carried out to find the wear-out areas. It was found that areas with a reduced hardness, where ball material destruction occurs, are formed on the surface during operation. To determine the changes in the material properties, an ultimate strength was tested. Its values in different parts of the ball with the time change were found. It was revealed that the discontinuity surface structure is the same for all areas and the entire time interval. This indicates the absence of phase transitions of ball materials during operation. Diagnostics of the surface structure by the electron beam was conducted. This work allows to forecast the destruction rate of balls during their use and identify priorities for improving their performance.
References
- Voinov, O. P., Polonik, V. S. (2012). Building of caldrons and development of energy is in Ukraine. Energy and electrification: Scientifically production magazine, 5, 41–45.
- Prokhorenko, E. M., Klepikov, V. F., Lytvynenko, V. V., Bazaleev, М. I., Bryukhovetskaya, O. E., Morozov, A. I., Zakharchenko, A. A., Safonov, I. Ya, Kolesnikova, V. V. (2012). IF- radiometry, as instrument of control of equipment of energygenerating objects. News of Donetsk mountain institute, 1 (30), 353–360.
- Klepikov, V. F., Annopol'skiy, D. A., Babushkina, S .I., Lytvynenko, V. V., Melyakova, E. A, Prokhorenko, E. M., Sagaydachnyy, M. A. (2014). Prospects of the use of radiation methods of cleaning of smoke gases and diagnostics of equipment for fuel of preparation. Compressor and power engineer, 2 (36), 34–38.
- Kesova, L. A. (2009). Influence of the system ardor of preparation on the fire-box mode of caldron at highly concentrated ardor to the serve on gas-rings. Energy and electrification: Scientifically production magazine, 5, 41–45.
- Levit, V. T. (1991). Ardor preparation on thermal power-stations. Moscow: Energoatomizdat, 384.
- Proskurovsky, D. I., Rotshtein, V. P., Ozur, G. E., Ivanov, Y. F., Markov, A. B. (2000). Physical foundations for surface treatment of materials with low energy, high current electron beams. Surface and Coatings Technology, 125 (1-3), 49–56. doi: 10.1016/s0257-8972(99)00604-0
- Zou, J. X., Zhang, K. M., Dong, C., Qin, Y., Hao, S. Z., Grosdidier, T. (2006). Selective surface purification via crater eruption under pulsed electron beam irradiation. Applied Physics Letters, 89 (4), 1904–1913. doi: 10.1063/1.2234306
- Hao, S. Z., Wu P. S., Zou, J. X., Grosdidier, T., Dong, C. (2007). Microstructure evolution occurring in the modified surface of 316L stainless steel under high current pulsed electron beam treatment. Applied Surface Science, 253 (12), 5349–5354. doi: 10.1016/j.apsusc.2006.12.011
- Zou, J. X., Grosdidier, T., Zhang, K. M., Dong, C. (2009). Cross-sectional analysis of the graded microstructure in an AISI D2-steeltreated with low energy high-current pulsed electron beam. Applied Surface Science, 255 (9), 4758–4764. doi: 10.1016/j.apsusc.2008.10.123
- ГОСТ 7524-89 (1989). Balls the steel grindings for ball mills Entered. 01.02.1989-01-02. Мoscow: publishing house of standards, 26.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2015 Евгений Михайлович Прохоренко, Вячеслав Федорович Клепиков, Владимир Викторович Литвиненко, Павел Александрович Хаймович, Николай Анатольевич Шульгин, Андрей Иванович Морозов
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.
