Elaboration of strength model of cylindrical joint with interference fit
DOI:
https://doi.org/10.15587/1729-4061.2015.42398Keywords:
strength of joins with interference fit, lower bound strength, the percentage of gamma-strength, failure rateAbstract
In the case of using the cylindrical joins with interference fit it is important to have a prediction of how much load it carries. For estimating the results of experiments the law of normal distribution is most often used. It is not suitable because of the physical reasons since it has no lower limit.
A three-parameter probabilistic model of the strength of the cylindrical joins with interference fit is proposed. It allows calculating the allowable carries value on the results of the small number of experiments. The model contains finite lower bound strength. It is found evaluation of all three model parameters and it is given the method of their calculation for small sample. It is explained the practical application of the model. The model is tested on the strength results experiments of 11 shaft-hub joins with diameter 60 mm. It confirmed its efficiency and effectiveness. An example of the strength and failure rate curves of joins is constructed, that is match with experimental data. Model will be use in mechanical engineering for predicting strength of the cylindrical joins in a case of limited number of experiments.
References
- Gallio, G., Lombardia, M., Rovarinob, D., Finoa, P., Montanaroa, L. (2013). Influence of the mechanical behaviour of different adhesives on an interference-fit cylindrical joint. International Journal of Adhesion and Adhesives, 47, 63–68. doi: 10.1016/j.ijadhadh.2013.09.021
- Sekercioglua, T., Gulsoza, A., Rendeb, H. (2005). The effects of bonding clearance and interference fit on the strength of adhesively bonded cylindrical components. Materials & Design, 26 (4), 377–381. doi: 10.1016/j.matdes.2004.05.016
- Kragelskiy, I. V., Dobyichin, M. N., Kombalov, V. S. (1977). Osnovyi raschetov na trenie i iznos. Moscow: Mashinostroenie, 526.
- Zenkin, A. S., Arpentev, B. M. (1987). Sborka nepodvizhnyih soedineniy termicheskimi metodami. Moscow: Mashinostroenie, 128.
- Kravtsov, M. K., Svyatuha, A. A., Chernov, V. V. (2001). Promezhutochnyie sredyi v soedineniyah s natyagom. Kharkiv: Shtrih, 200.
- Sen, S., Aksakal, B. (2004). Stress analysis of interference fitted shaft–hub system under transient heat transfer conditions. Materials & Design, 25 (5), 63–68. doi: 10.1016/j.matdes.2003.11.009
- Boutoutaou, H., Bouazizb, M., Fontaine, J. F. (2011). Modeling of interference fits taking form defects of the surfaces in contact into account. Materials & Design, 32 (7), 3692–3701. doi: 10.1016/j.matdes.2011.03.059
- Chakherlou, T. N., Abazadeh, B. (2012). Experimental and numerical investigations about the combined effect of interference fit and bolt clamping on the fatigue behavior of Al 2024-T3 double shear lap joints. Materials & Design, 33, 425–435. doi: 10.1016/j.matdes.2011.04.045
- Mucha, J. (2009). Finite element modeling and simulating of thermomechanic stress in thermocompression bondings. Materials & Design, 30 (4), 1174–1182. doi: 10.1016/j.matdes.2008.06.026
- Gnedenko, B. V. (1941) Predelnyie teoremyi dlya maksimalnogo chlena variatsionnogo ryada. DAN SSSR, 32 (1), 7.
- Fihtengolts, G. M. (1969). Kurs differentsialnogo i integralnogo ischisleniya (7-e izd.). Moscow: Nauka, 794.
- Deyvid, G. (1979). Poryadkovyie statistiki. Moscow: Nauka, 336.
- Lamnauer, N. Yu. (2012). Model raspredeleniya razmerov izdeliy i ee primenenie dlya otsenki tochnosti obrabotki. Visnik Natsionalnogo tehnichnogo universitetu «Harkivskiy politehnichniy Institut». Zbirnik naukovih prats. Tematichniy vipusk: Matematichne modelyuvannya v tehnitsi ta tehnologiyah, 27, 98–107.
- Kupriyanov, A. V. (2012). Eksperimentalnoe issledovanie vliyaniya pogreshnosti geometrii formyi detaley na prochnost tsilindricheskogo soedineniya s natyagom. Mashinobuduvannya: Zbirnik naukovih prats, 10, 85–93.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2015 Александр Владимирович Куприянов, Наталия Юрьевна Ламнауэр
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.
