Researching of pressure influence at the structure and properties rolled wire from Steel 20

Authors

  • Николай Николаевич Бережной DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027, Ukraine
  • Виктория Анатольевна Чубенко DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027, Ukraine
  • Сергей Олегович Мацышин DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027, Ukraine
  • Анна Шепель DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2012.4913

Keywords:

deformation, structure, degree and temperature of deformation.

Abstract

The problem of researching of pressure influence at structure and properties of rolled wire low-carbon steel has been formulated in this article. Temperature-deformation condition of steel 20 and dependences at the size of grain due to degree and temperature of deformation were built.

Author Biographies

Николай Николаевич Бережной, DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027

Doctor of technical science, Associate Professor

Department of Metal pressure working and metallurgical equipment

Виктория Анатольевна Чубенко, DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027

Ph.D

Department of Metal pressure working and metallurgical equipment

Сергей Олегович Мацышин, DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027

Postgraduate student, assistant of chair

Department of Metal pressure working and metallurgical equipment

Анна Шепель, DVNZ “Krivorozkiy national University” str. 22th Partsiezda,11, Krivoy Rog, Ukraine, 50027

Master

Department of Metal pressure working and metallurgical equipment

References

  1. Milieu, Y.J. Новые разработки в области проволочных станов// Y.J. Milieu, D. Bude D. Журнал «Новости черной металлургии за рубежом». 2001. №4 (28). С. 67-70.
  2. ГОСТ 5639-82. Стали и сплавы. Методы выявления и определения величины зерна. [Текст]. — Введ. 01.08.2003, переиздание с изм. 1. — М.: Изд-во стандартов, 2003. — 30 с.
  3. Конструкция пластометра торсионного типа / Ф.В. Капцан, В.Н. Урцев, С.А. Морозов, В.Н. Дегтярев, И.Л. Белевский, А.А. Николаев // В кн. Совершенствование технологии на ОАО ММК / Сб. тр. Центральной лаборатории контроля. - 1999. - Вып. 3. - С. 321 - 324.

Downloads

Published

2012-07-05

How to Cite

Бережной, Н. Н., Чубенко, В. А., Мацышин, С. О., & Шепель, А. (2012). Researching of pressure influence at the structure and properties rolled wire from Steel 20. Eastern-European Journal of Enterprise Technologies, 4(5(58), 4–6. https://doi.org/10.15587/1729-4061.2012.4913

Issue

Vol. 4 No. 5(58) (2012): The applied physics and materials technology

Section

Applied physics

License

Copyright (c) 2014 Николай Николаевич Бережной, Виктория Анатольевна Чубенко, Сергей Олегович Мацышин, Анна Шепель

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.