Experimental study of heat transfer and hydraulic resistance at cross flow of tube bundle with indentations

Authors

DOI:

https://doi.org/10.15587/1729-4061.2017.108576

Keywords:

tube bundle, cross flow, surface indentations, heat transfer coefficient, Euler number

Abstract

The results are given on experimental study of heat transfer and hydraulic losses at the cross flow of a five-row tube bundle arranged in the staggered mode, the external surface of which is covered with conic-shaped dimples. The tube’s spatially averaged heat transfer was measured by means of the melting ice technique. As a result, the heat transfer coefficients were determined both for separate tube rows and the whole bundle. The hydraulic losses of the tube bundle were also found for the same conditions in the form of the Euler number. The Reynolds number was defined on the external tube diameter and flow velocity in the minimal cross section of the bundle and was in the range of 3000…25000. In the heat transfer determination, the surface of a smooth cylinder was used without the surface of the dimple area. The heat transfer augmentation rate of 34…40 % at the pressure losses growth by 10…15 % was obtained. The Reynolds analogy factor (thermal performance) value is 1.17…1.27. The similarity relations for the Nusselt number and Euler number as a function of the Reynolds number were obtained. These relationships allow determining the coefficients of heat transfer and hydraulic resistance in the development of tube-type heat exchange equipment. The results of this study can be used for the development of compact tube-type heat exchangers with a high thermo-hydraulic performance parameter.

Author Biographies

Anton Meyris, Institute of Engineering Thermophysics of National academy of sciences of Ukraine Zhelyabov str., 2a, Kyiv, Ukraine, 03057

Postgraduate student

Department of Thermogasdynamic 

Artem Khalatov, Institute of Engineering Thermophysics of National academy of sciences of Ukraine Zhelyabov str., 2a, Kyiv, Ukraine, 03057

Doctor of Technical Sciences, Professor, Head of Department, Academician of NAS of Ukraine

Department of Thermogasdynamic 

Gleb Kovalenko, Institute of Engineering Thermophysics of National academy of sciences of Ukraine Zhelyabov str., 2a, Kyiv, Ukraine, 03057

PhD

Department of Thermogasdynamic 

References

  1. Bearman, P. W., Harvey, J. K. (1993). Control of circular cylinder flow by the use of dimples. AIAA Journal, 31 (10), 1753–1756. doi: 10.2514/3.11844
  2. Kozlov, A. P., Shchukin, A. V., Agachev, R. S. (1994). Gidrodinamicheskie effekty ot sfericheskih uglubleniy na poverhnosti poperechnoobtekaemogo tsilindra. Aviatsionnaya tekhnika. Izvestiya vysshih uchebnyh zavedeniy, 2, 27–34.
  3. Kovalenko, G. V., Khalatov, A. A. (2003). Fluid Flow and Heat Transfer Features at a Cross-Flow of Dimpled Tubes in a Confined Space. Volume 5: Turbo Expo 2003, Parts A and B. doi: 10.1115/gt2003-38155
  4. Butt, U., Egbers, C. (2013). Aerodynamic Characteristics of Flow over Circular Cylinders with Patterned Surface. International Journal of Materials, Mechanics and Manufacturing, 121–125. doi: 10.7763/ijmmm.2013.v1.27
  5. Zhou, B., Wang, X., Guo, W., Gho, W. M., Tan, S. K. (2015). Control of flow past a dimpled circular cylinder. Experimental Thermal and Fluid Science, 69, 19–26. doi: 10.1007/978-3-642-56535-9_92
  6. Shchelchkov, A. V. (2016). Gidravlicheskoe soprotivlenie trubnyh puchkov s polusfericheskimi kavernami. Vestnik Kazanskogo gosudarstvennogo tekhnicheskogo universiteta, 71 (3), 10–15.
  7. Belen'kiy, M. Ya., Gotovskiy, M. A., Lekah, B. M., Fokin, B. S. (1995). Teplogidravlicheskie harakteristiki poperechno obtekamyh poverhnostey s lunkami. Teploenergetika, 4, 49–51.
  8. Sherrow, L. D., Ligrani, P. M., Chudnovsky, Y. P., Kozlov, A. P. (2006). Effects of Exterior Surface Dimples on Heat Transfer and Friction Factors for a Cross-Flow Heat Exchanger. Journal of Enhanced Heat Transfer, 13 (1), 1–16. doi: 10.1615/jenhheattransf.v13.i1.10
  9. Bearman, P. W., Harvey, J. K. (1976). Golf Ball Aerodynamics. Aeronautical Quarterly, 27 (02), 112–122. doi: 10.1017/s0001925900007617
  10. Moon, S. W., Lau, S. C. (2002). Turbulent Heat Transfer Measurements on a Wall With Concave and Cylindrical Dimples in a Square Channel. Volume 3: Turbo Expo 2002, Parts A and B. doi: 10.1115/gt2002-30208
  11. Kovalenko, G. V., Halatov, A. A. (2008). Primenenie ledyanyh kalorimetrov dlya issledovaniya teplootdachi poverhnostey, formirovannyh uglubleniyami. Promyshlennaya teplotekhnika, 2, 5–12.
  12. Isachenko, V. P., Osipova, V. A., Sukomel, A. S. (1981). Teploperedacha. Moscow: Energoizdat, 416.
  13. Dyban, E. P., Epik, E. Ya. (1985). Teplomassoobmen i gidrodinamika turbulizirovannyh potokov. Kyiv: Naukova dumka, 296.
  14. Shmidt, F., Henderson, R., Wolgemuth, C. (1984). Introduction to Thermal Sciences. John Wiley & Son, New York, NY, 445.
  15. Rabas, T. J., Webb, R. L., Thors, P., Kim, N.-K. (1993). Influence of Roughness Shape and Spacing on the Performance of Three-Dimensional Helically Dimpled Tubes. Journal of Enhanced Heat Transfer, 1 (1), 53–64. doi: 10.1615/jenhheattransf.v1.i1.50

Downloads

Published

2017-08-31

How to Cite

Meyris, A., Khalatov, A., & Kovalenko, G. (2017). Experimental study of heat transfer and hydraulic resistance at cross flow of tube bundle with indentations. Eastern-European Journal of Enterprise Technologies, 4(8 (88), 17–21. https://doi.org/10.15587/1729-4061.2017.108576

Issue

Vol. 4 No. 8 (88) (2017): Energy-saving technologies and equipment

Section

Energy-saving technologies and equipment

License

Copyright (c) 2017 Anton Meyris, Artem Khalatov, Gleb Kovalenko

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.