Establishing the effect of decreased power intensity of self-oscillatory grinding in a tumbling mill when the crushed material content in the intra-chamber fill is reduced

Authors

DOI:

https://doi.org/10.15587/1729-4061.2020.209050

Keywords:

tumbling mill, content of crushed material in intra-chamber fill, self-oscillations, energy intensity of grinding

Abstract

The influence of the content of crushed material in the intra-chamber grinding fill on the efficiency of the self-oscillatory grinding process in the tumbling mill was assessed.

A dynamic effect of a significant decrease in self-oscillatory action of the two-fraction fill of the rotary chamber with an increase in the content of fine fraction was revealed by the method of visual analysis of motion patterns. A decrease in values of the following inertial fill parameters was established: maximum dilatancy υmax, the relative amplitude of self-oscillations ψRυ and a maximum share of the active part κfam max with an increase in the degree of filling the gaps between particles of the coarse fraction κmbgr. A decrease in the generalized complex degree of dynamic activation Ka was also established. The effect is due to the strengthening of the cohesive properties of the incoherent coarse fraction under the influence of the fine fraction. There was a decrease in by 29 % for υmax, by 7 % for ψRυ, 2.9 times for κfam max and 4.2 times for Ka with an increase in κmbgr from 0 to 1 at the degree of filling the chamber with the fill κbr=0.45.

Technological effect of a significant decrease in specific energy intensity and an increase in productivity of the innovative self-oscillatory grinding process in comparison with characteristics of the conventional steady-state process at a decrease in the content of crushed material in the fill was established.

A process of milling cement clinker with grinding bodies at relative size of 0.026 and κbr=0.45 was considered. A decrease in specific energy intensity by 27 % at κmbgr=1, by 38 % at κmbgr=0.5625 and by 44 % at κmbgr=0 was found. An increase in relative productivity by 7 % at κmbgr=1, by 26 % at κmbgr=0.5625 and by 39 % at κmbgr=0.125 was established.

The established effects will make it possible to forecast rational parameters of the self-oscillatory grinding process in a tumbling mill at the variation of the content of the crushed material in the fill

Author Biographies

Kateryna Deineka, Technical College National University of Water and Environmental Engineering Soborna str., 11, Rivne, Ukraine, 33028

PhD

Yuriy Naumenko, National University of Water and Environmental Engineering Soborna str., 11, Rivne, Ukraine, 33028

Doctor of Technical Sciences, Associate Professor

Department of Construction, Road, Reclamation, Agricultural Machines and Equipment

References

  1. Naumenko, Yu. V. (1999). The antitorque moment in a partially filled horizontal cylinder. Theoretical Foundations of Chemical Engineering, 33 (1), 91–95.
  2. Naumenko, Yu. V. (2000). Determination of rational rotation speeds of horizontal drum machines. Metallurgical and Mining Industry, 5, 89–92.
  3. Naumenko, Y. (2017). Modeling of fracture surface of the quasi solid-body zone of motion of the granular fill in a rotating chamber. Eastern-European Journal of Enterprise Technologies, 2 (1 (86)), 50–57. doi: https://doi.org/10.15587/1729-4061.2017.96447
  4. Naumenko, Y., Sivko, V. (2017). The rotating chamber granular fill shear layer flow simulation. Eastern-European Journal of Enterprise Technologies, 4 (7 (88)), 57–64. doi: https://doi.org/10.15587/1729-4061.2017.107242
  5. Naumenko, Y. (2017). Modeling a flow pattern of the granular fill in the cross section of a rotating chamber. Eastern-European Journal of Enterprise Technologies, 5 (1 (89)), 59–69. doi: https://doi.org/10.15587/1729-4061.2017.110444
  6. Lv, J., Wang, Z., Ma, S. (2020). Calculation method and its application for energy consumption of ball mills in ceramic industry based on power feature deployment. Advances in Applied Ceramics, 119 (4), 183–194. doi: https://doi.org/10.1080/17436753.2020.1732621
  7. Deineka, K. Y., Naumenko, Y. V. (2018). The tumbling mill rotation stability. Scientific Bulletin of National Mining University, 1, 60–68. doi: https://doi.org/10.29202/nvngu/2018-1/10
  8. Deineka, K., Naumenko, Y. (2019). Revealing the effect of decreased energy intensity of grinding in a tumbling mill during self-excitation of auto-oscillations of the intrachamber fill. Eastern-European Journal of Enterprise Technologies, 1 (1 (97)), 6–15. doi: https://doi.org/10.15587/1729-4061.2019.155461
  9. Deineka, K., Naumenko, Y. (2019). Establishing the effect of a decrease in power intensity of self-oscillating grinding in a tumbling mill with a reduction in an intrachamber fill. Eastern-European Journal of Enterprise Technologies, 6 (7 (102)), 43–52. doi: https://doi.org/10.15587/1729-4061.2019.183291
  10. Gupta, V. K. (2020). Energy absorption and specific breakage rate of particles under different operating conditions in dry ball milling. Powder Technology, 361, 827–835. doi: https://doi.org/10.1016/j.powtec.2019.11.033
  11. Cleary, P. W., Morrison, R. D. (2011). Understanding fine ore breakage in a laboratory scale ball mill using DEM. Minerals Engineering, 24 (3-4), 352–366. doi: https://doi.org/10.1016/j.mineng.2010.12.013
  12. Cleary, P. W., Owen, P. (2019). Effect of operating condition changes on the collisional environment in a SAG mill. Minerals Engineering, 132, 297–315. doi: https://doi.org/10.1016/j.mineng.2018.06.027
  13. Yin, Z., Peng, Y., Zhu, Z., Yu, Z., Li, T. (2017). Impact Load Behavior between Different Charge and Lifter in a Laboratory-Scale Mill. Materials, 10 (8), 882. doi: https://doi.org/10.3390/ma10080882
  14. Öksüzoğlu, B., Uçurum, M. (2016). An experimental study on the ultra-fine grinding of gypsum ore in a dry ball mill. Powder Technology, 291, 186–192. doi: https://doi.org/10.1016/j.powtec.2015.12.027
  15. Deniz, V. (2016). The effects of powder filling on the kinetic breakage parameters of natural amorphous silica. Particulate Science and Technology, 35 (6), 682–687. doi: https://doi.org/10.1080/02726351.2016.1194347
  16. Yin, Z., Peng, Y., Zhu, Z., Yu, Z., Li, T., Zhao, L., Xu, J. (2017). Experimental study of charge dynamics in a laboratory-scale ball mill. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 232 (19), 3491–3499. doi: https://doi.org/10.1177/0954406217738031
  17. Cayirli, S. (2018). Influences of operating parameters on dry ball mill performance. Physicochemical Problems of Mineral Processing, 54 (3), 751–762. doi: http://doi.org/10.5277/ppmp1876
  18. Katubilwa, F. M., Moys, M. H. (2011). Effects of filling degree and viscosity of slurry on mill load orientation. Minerals Engineering, 24 (13), 1502–1512. doi: https://doi.org/10.1016/j.mineng.2011.08.004
  19. Mulenga, F. K., Moys, M. H. (2014). Effects of slurry filling and mill speed on the net power draw of a tumbling ball mill. Minerals Engineering, 56, 45–56. doi: https://doi.org/10.1016/j.mineng.2013.10.028
  20. Mulenga, F. K., Moys, M. H. (2014). Effects of slurry pool volume on milling efficiency. Powder Technology, 256, 428–435. doi: https://doi.org/10.1016/j.powtec.2014.02.013
  21. Mulenga, F. K., Mkonde, A. A., Bwalya, M. M. (2016). Effects of load filling, slurry concentration and feed flowrate on the attainable region path of an open milling circuit. Minerals Engineering, 89, 30–41. doi: https://doi.org/10.1016/j.mineng.2016.01.002
  22. Soleymani, M. M., Fooladi Mahani, M., Rezaeizadeh, M. (2016). Experimental observations of mill operation parameters on kinematic of the tumbling mill contents. Mechanics & Industry, 17 (4), 408. doi: https://doi.org/10.1051/meca/2015077
  23. Soleymani, M. M., Fooladi, M., Rezaeizadeh, M. (2016). Effect of slurry pool formation on the load orientation, power draw, and impact force in tumbling mills. Powder Technology, 287, 160–168. doi: https://doi.org/10.1016/j.powtec.2015.10.009
  24. Soleymani, M. M., Fooladi, M., Rezaeizadeh, M. (2016). Experimental investigation of the power draw of tumbling mills in wet grinding. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 230 (15), 2709–2719. doi: https://doi.org/10.1177/0954406215598801
  25. Soleymani, M., Fooladi Mahani, M., Rezaeizadeh, M. (2016). Experimental study the impact forces of tumbling mills. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 231 (2), 283–293. doi: https://doi.org/10.1177/0954408915594526
  26. Yin, Z., Peng, Y., Zhu, Z., Ma, C., Yu, Z., Wu, G. (2019). Effect of mill speed and slurry filling on the charge dynamics by an instrumented ball. Advanced Powder Technology, 30 (8), 1611–1616. doi: https://doi.org/10.1016/j.apt.2019.05.009

Downloads

Published

2020-08-31

How to Cite

Deineka, K., & Naumenko, Y. (2020). Establishing the effect of decreased power intensity of self-oscillatory grinding in a tumbling mill when the crushed material content in the intra-chamber fill is reduced. Eastern-European Journal of Enterprise Technologies, 4(1 (106), 39–48. https://doi.org/10.15587/1729-4061.2020.209050

Issue

Vol. 4 No. 1 (106) (2020): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2020 Kateryna Deineka, Yuriy Naumenko

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.