Determining the mechanical characteristics of composite materials reinforced with woven preforms
DOI:
https://doi.org/10.15587/1729-4061.2021.225112Keywords:
sleeve, premix, reinforcement angle, rod model, fibers, binder, test, stretching, bending, compressionAbstract
Reduction of the complexity of production of articles from composite materials is largely ensured by the use of reinforcing semi-finished products in which fibers pre-form a framework. Among all the variety of reinforcing systems, woven sleeves (preforms) occupy a special place. The high degree of deformability in a nonimpregnated condition makes it possible to lay this reinforcement on any surface without folds and cuts that provide preservation of strand continuity. This advantage of woven sleeves is accompanied by a change in local reinforcement angles and, consequently, the variable nature of physical and mechanical characteristics of the curved part surface. A method for calculating physical and mechanical characteristics of the composite based on preforms at any point of the part depending on the pattern of laying strands on a curved surface has been developed. The possibility of application of the rod model of the composite to describe physical and mechanical characteristics of the composite material with a woven reinforcement was analyzed. The model essence consists in that the composite is modeled by a diamond-shaped rod system. The rhombus sides serve as fibers and the diagonals as the binder. To verify the theoretical results and substantiate practical recommendations, a series of experimental studies were performed based on the formation of material specimens from two types of woven sleeves with different reinforcement angles. The experimental study program included tensile, bending, and compression tests. A fairly good convergence of theoretical and experimental data was obtained. For example, a square of the correlation coefficient was not less than 0.95 for the modulus of elasticity, not less than 0.8 for the Poisson's ratio, and not less than 0.9 for tensile and compressive strengths. This is the rationale for using the rod model to describe the considered class of composites. The use of the developed procedure will make it possible to increase the perfection of the considered class of designs and obtain rational parameters of the process of their manufacture.
References
- Fomin, O., Logvinenko, O., Burlutsky, O., Rybin, A. (2018). Scientific Substantiation of Thermal Leveling for Deformations in the Car Structure. International Journal of Engineering & Technology, 7 (4.3), 125. doi: https://doi.org/10.14419/ijet.v7i4.3.19721
- Bychkov, A. S., Kondratiev, A. V. (2019). Criterion-Based Assessment of Performance Improvement for Aircraft Structural Parts with Thermal Spray Coatings. Journal of Superhard Materials, 41 (1), 53–59. doi: https://doi.org/10.3103/s1063457619010088
- Mustafa, L. M., Ismailov, M. B., Sanin, A. F. (2020). Study on the effect of plasticizers and thermoplastics on the strength and toughness of epoxy resins. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, 4, 63–68. doi: https://doi.org/10.33271/nvngu/2020-4/063
- Kondratiev, A., Slivinsky, M. (2018). Method for determining the thickness of a binder layer at its non-uniform mass transfer inside the channel of a honeycomb filler made from polymeric paper. Eastern-European Journal of Enterprise Technologies, 6 (5 (96)), 42–48. doi: https://doi.org/10.15587/1729-4061.2018.150387
- Rodichev, Y. M., Smetankina, N. V., Shupikov, O. M., Ugrimov, S. V. (2018). Stress-Strain Assessment for Laminated Aircraft Cockpit Windows at Static and Dynamic Loads. Strength of Materials, 50 (6), 868–873. doi: https://doi.org/10.1007/s11223-019-00033-4
- Kondratiev, A., Gaidachuk, V., Nabokina, T., Tsaritsynskyi, A. (2020). New Possibilities of Creating the Efficient Dimensionally Stable Composite Honeycomb Structures for Space Applications. Advances in Intelligent Systems and Computing, 45–59. doi: https://doi.org/10.1007/978-3-030-37618-5_5
- Leong, K. H., Ramakrishna, S., Huang, Z. M., Bibo, G. A. (2000). The potential of knitting for engineering composites – a review. Composites Part A: Applied Science and Manufacturing, 31 (3), 197–220. doi: https://doi.org/10.1016/s1359-835x(99)00067-6
- Donetskiy, K. I., Kogan, D. I., Khrulkov, A. V. (2014). Properties of the polymeric composite materials made on the basis of braided preforms. Proceedings of VIAM, 3. doi: https://doi.org/10.18577/2307-6046-2014-0-3-5-5
- Okano, M., Sugimoto, K., Saito, H., Nakai, A., Hamada, H. (2005). Effect of the braiding angle on the energy absorption properties of a hybrid braided FRP tube. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 219 (1), 59–66. doi: https://doi.org/10.1243/146442005x10256
- Erber, A., Drechsler, K. (2009). Torsional performance and damage tolerance of braiding configurations. JEC Composites Magazine, 46, 42–45.
- Arold, B., Gessler, A., Metzner, C., Birkefeld, K. (2015). Braiding processes for composites manufacture. Advances in Composites Manufacturing and Process Design, 3–26. doi: https://doi.org/10.1016/b978-1-78242-307-2.00001-4
- Birkefeld, K., Pickett, A., Middendorf, P. (2018). 8.5 Virtual Design and Optimisation of Braided Structures Considering Production Aspects of the Preform. Comprehensive Composite Materials II, 85–97. doi: https://doi.org/10.1016/b978-0-12-803581-8.10054-2
- Li, X., Binienda, W. K., Littell, J. D. (2009). Methodology for Impact Modeling of Triaxial Braided Composites Using Shell Elements. Journal of Aerospace Engineering, 22 (3), 310–317. doi: https://doi.org/10.1061/(asce)0893-1321(2009)22:3(310)
- Lomov, S. V., Parnas, R. S., Bandyopadhyay Ghosh, S., Verpoest, I., Nakai, A. (2002). Experimental and Theoretical Characterization of the Geometry of Two-Dimensional Braided Fabrics. Textile Research Journal, 72 (8), 706–712. doi: https://doi.org/10.1177/004051750207200810
- Lomov, S. V., Mikolanda, T., Kosek, M., Verpoest, I. (2007). Model of internal geometry of textile fabrics: Data structure and virtual reality implementation. Journal of the Textile Institute, 98 (1), 1–13. doi: https://doi.org/10.1533/joti.2006.0251
- Verleye, B., Croce, R., Griebel, M., Klitz, M., Lomov, S. V., Morren, G. et. al. (2008). Permeability of textile reinforcements: Simulation, influence of shear and validation. Composites Science and Technology, 68 (13), 2804–2810. doi: https://doi.org/10.1016/j.compscitech.2008.06.010
- Zílio, L., Dias, M., Santos, T., Santos, C., Fonseca, R., Amaral, A., Aquino, M. (2020). Characterization and statistical analysis of the mechanical behavior of knitted structures used to reinforce composites: Yarn compositions and float stitches. Journal of Materials Research and Technology, 9 (4), 8323–8336. doi: https://doi.org/10.1016/j.jmrt.2020.05.089
- Samipour, S. A., Khaliulin, V. I., Batrakov, V. V. (2017). A method for calculating the parameters for manufacturing preforms via radial braiding. Journal of Machinery Manufacture and Reliability, 46 (3), 302–308. doi: https://doi.org/10.3103/s1052618817030128
- Samipur, S. A., Danilov, Y. S. (2016). Development and verification of an analytic technique to determine the stiffness parameters of braided tubular parts. Russian Aeronautics, 59 (4), 460–465. doi: https://doi.org/10.3103/s1068799816040048
- Chen, C. M., Kam, T. Y. (2007). Elastic constants identification of symmetric angle-ply laminates via a two-level optimization approach. Composites Science and Technology, 67 (3-4), 698–706. doi: https://doi.org/10.1016/j.compscitech.2006.04.016
- Kondratiev, A., Gaidachuk, V., Nabokina, T., Kovalenko, V. (2019). Determination of the influence of deflections in the thickness of a composite material on its physical and mechanical properties with a local damage to its wholeness. Eastern-European Journal of Enterprise Technologies, 4 (1 (100)), 6–13. doi: https://doi.org/10.15587/1729-4061.2019.174025
- Andreev, A. V., Karpov, Ya. S. (2010). Modelirovanie uprugih i prochnostnyh svoystv kompozitov, armirovannyh pletenymi rukavami. Voprosy proektirovaniya i proizvodstva konstruktsiy letatel'nyh apparatov, 4 (64), 7–10.
- Kondratiev, A., Andrieiev, O. (2020). Forecasting characteristics of composite strength on the basis of preforms in elements of building structures. Municipal economy of cities, 6 (159), 2–9. doi: https://doi.org/10.33042/2522-1809-2020-6-159-2-9
- Chaouachi, F., Rahali, Y., Ganghoffer, J. F. (2014). A micromechanical model of woven structures accounting for yarn–yarn contact based on Hertz theory and energy minimization. Composites Part B: Engineering, 66, 368–380. doi: https://doi.org/10.1016/j.compositesb.2014.05.027
- Karpov, Y. S., Lepikhin, P. P., Taranenko, I. M. (2001). Mechanics of composite materials. Kharkiv: National Aerospace University “Kharkiv Aviation Institute” Publ., 104.
- Wang, H., Wang, Z. (2015). Quantification of effects of stochastic feature parameters of yarn on elastic properties of plain-weave composite. Part 1: Theoretical modeling. Composites Part A: Applied Science and Manufacturing, 78, 84–94. doi: https://doi.org/10.1016/j.compositesa.2015.07.022
- Wu, L., Zhang, F., Sun, B., Gu, B. (2014). Finite element analyses on three-point low-cyclic bending fatigue of 3-D braided composite materials at microstructure level. International Journal of Mechanical Sciences, 84, 41–53. doi: https://doi.org/10.1016/j.ijmecsci.2014.03.036
- Wu, Z., Au, C. K., Yuen, M. (2003). Mechanical properties of fabric materials for draping simulation. International Journal of Clothing Science and Technology, 15 (1), 56–68. doi: https://doi.org/10.1108/09556220310461169
- Kondratiev, A. (2019). Improving the mass efficiency of a composite launch vehicle head fairing with a sandwich structure. Eastern-European Journal of Enterprise Technologies, 6 (7 (102)), 6–18. doi: https://doi.org/10.15587/1729-4061.2019.184551
- Ahmadi, M. S., Johari, M. S., Sadighi, M., Esfandeh, M. (2009). An experimental study on mechanical properties of GFRP braid-pultruded composite rods. Express Polymer Letters, 3 (9), 560–568. doi: https://doi.org/10.3144/expresspolymlett.2009.70
- Pellegrino, S. (2012). Satellite Hardware: Stow-and-Go for Space Travel. Advanced Materials and Processes, 170, 39–41.
- Arnold, W., William, A., Wieslaw, B., Robert, G., Lee, K., Justin, L., Gary, R. (2009). Characterization of Triaxial Braided Composite Material Properties for Impact Simulation. 65-th American Helicopter Society International Annual Forum, 2, 912–933.
- Balea, L., Dusserre, G., Bernhart, G. (2014). Mechanical behaviour of plain-knit reinforced injected composites: Effect of inlay yarns and fibre type. Composites Part B: Engineering, 56, 20–29. doi: https://doi.org/10.1016/j.compositesb.2013.07.028
- Bergmann, T., Heimbs, S., Maier, M. (2015). Mechanical properties and energy absorption capability of woven fabric composites under ±45° off-axis tension. Composite Structures, 125, 362–373. doi: https://doi.org/10.1016/j.compstruct.2015.01.040
- Boufaida, Z., Farge, L., André, S., Meshaka, Y. (2015). Influence of the fiber/matrix strength on the mechanical properties of a glass fiber/thermoplastic-matrix plain weave fabric composite. Composites Part A: Applied Science and Manufacturing, 75, 28–38. doi: https://doi.org/10.1016/j.compositesa.2015.04.012
- Ayranci, C., Carey, J. P. (2011). Experimental validation of a regression-based predictive model for elastic constants of open mesh tubular diamond-braid composites. Polymer Composites, 32 (2), 243–251. doi: https://doi.org/10.1002/pc.21042
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Марина Анатольевна Шевцова, Андрей Валерьевич Кондратьев, Алексей Викторович Андреев
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.