Modeling and automation of brick kilns

Authors

  • Оксана Викторовна Симчук Кафедра автоматизации теплоэнергетических процессов Национальный технический университет Украины «Киевский политехнический институт», Ukraine
  • Валерий Федорович Мысак Теплоэнергетический факультет Национальный технический университет Украины «Киевский политехнический институт», Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2010.3243

Keywords:

tunel stove, design, method of Brandon

Abstract

The described system of automation of stove is for firing of brick. Resulted results of design of area of burning - out the method of Brandon, that enable to forecast appearance of defective products.

Author Biographies

Оксана Викторовна Симчук, Кафедра автоматизации теплоэнергетических процессов Национальный технический университет Украины «Киевский политехнический институт»

Магистрант

Валерий Федорович Мысак, Теплоэнергетический факультет Национальный технический университет Украины «Киевский политехнический институт»

Кандидат технических наук, доцент, заместитель декана по методической работе

References

  1. Дис. канд. техн. наук: 05.13.07 / І.М. Голінко; Укр. держ. ун-т харч. технологій. — К., 2000. — 181 с. — укp.
  2. Дис. канд. техн. наук: 05.13.07 / І.В. Ярощук; Нац. техн. ун-т України ”Київ. політехн. ін-т”. — К., 2003. — 286 с. — укp.

Downloads

Published

2010-11-10

How to Cite

Симчук, О. В., & Мысак, В. Ф. (2010). Modeling and automation of brick kilns. Eastern-European Journal of Enterprise Technologies, 6(3(48), 29–31. https://doi.org/10.15587/1729-4061.2010.3243

Issue

Vol. 6 No. 3(48) (2010): Control systems

Section

Control systems

License

Copyright (c) 2014 Оксана Викторовна Симчук, Валерий Федорович Мысак

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.