Selection of an optimum method of mechanical treatment, based upon the conditions of strength of cutting tools

Authors

  • I. E. Ivanov ДВНЗ «Приазовський державний технічний університет», м. Маріуполь, Ukraine

DOI:

https://doi.org/10.31498/2225-6733.24.2012.19817

Keywords:

tool pieces, durability, optimization, efficiency, abrasive polishing, productivity

Abstract

Technological capabilities of cutting (blade and abrasive) tools were theoretically substantiated from the point of view of their strength. Determined were optimal correlation between the ultimate shearing  strength of the material and the cutting tool, which are realized for a zero front angle of the tool and eliminates the possibility of destruction of tool’s cutting section during the process of cutting. Efficiency of application of ultra-hard surface deposited materials of abrasive polishing was proved, allowing to perform more productive and quality treatment, as compared to blade cutting tools

Author Biography

I. E. Ivanov, ДВНЗ «Приазовський державний технічний університет», м. Маріуполь

Кандидат технічних наук, старший викладач

References

Рыбицкий В.А. Опыт внедрения алмазного шлифования деталей с защитными покрытиями / В.А. Рыбицкий. − К.: Общество «Знание» УССР, 1987. − 23 с.

Новиков Ф.В. Технологическое обеспечение высококачественной обработки деталей с износостойкими наплавками металлургического назначения / Ф.В. Новиков, В.А. Андилахай // Наукові праці Донецького національного технічного університету. Серія : Машинобудування і машинознавство. − Донецьк: ДонНТУ. − 2010. − Вип. 7 (166). − С. 53-60.

Андилахай В.А. Выбор оптимальной схемы шлифования контактных (наплавленных) поверхностей крупногабаритных изделий металлургического назначения / В.А. Андилахай // Труды 16-й Международной научно-технической конференции. Физические и компьютерные технологии. – Харьков : ХНПК «ФЭД». − 2010. − С. 119-124.

Физико-математическая теория процессов обработки материалов и технологии машиностроения / Под общ. ред. Ф.В. Новикова и А.В. Якимова. В десяти томах. – Т. 3. «Резание материалов лезвийными инструментами» – Одесса: ОНПУ, 2003. – 546 с.

Физико-математическая теория процессов обработки материалов и технологии машиностроения / Под общ. ред. Ф.В. Новикова и А.В. Якимова. В десяти томах. – Т. 1. «Механика резания материалов» – Одесса: ОНПУ, 2002. – 580 с.

Downloads

How to Cite

Ivanov, I. E. (2013). Selection of an optimum method of mechanical treatment, based upon the conditions of strength of cutting tools. Reporter of the Priazovskyi State Technical University. Section: Technical Sciences, (24), 231–236. https://doi.org/10.31498/2225-6733.24.2012.19817

Issue

No. 24 (2012): Reporter of the Priazovskyi State Technical University. Section: Technical sciences

Section

Mechanical engineering and metal working

License

The journal «Reporter of the Priazovskyi State Technical University. Section: Technical sciences» is published under the CC BY license (Attribution License).

This license allows for the distribution, editing, modification, and use of the work as a basis for derivative works, even for commercial purposes, provided that proper attribution is given. It is the most flexible of all available licenses and is recommended for maximum dissemination and use of non-restricted materials.

Authors who publish in this journal agree to the following terms:

1. Authors retain the copyright of their work and grant the journal the right of first publication under the terms of the Creative Commons Attribution License (CC BY). This license allows others to freely distribute the published work, provided that proper attribution is given to the original authors and the first publication of the work in this journal is acknowledged.

2. Authors are allowed to enter into separate, additional agreements for non-exclusive distribution of the work in the same form as published in this journal (e.g., depositing it in an institutional repository or including it in a monograph), provided that a reference to the first publication in this journal is maintained.