Optimization of temperature measurement on the bus drum brake as a basis for developing brake fault signals
DOI:
https://doi.org/10.15587/1729-4061.2021.224907Keywords:
brake fault, traffic accident, brake temperature, temperature measurement, drum brakeAbstract
Brake failure is always possible due to several factors that are difficult to control, such as a slight leak in the brake hose due to an impact or a rat bite. In the latest research, the development of a brake performance detection tool has been started, but how to detect a brake temperature more efficiently on the brakes of large vehicles has not been specified. Given the significant impact of losses due to brake failure and accidents that are still occurring, this research plays an important role. It must be completed immediately so that accident cases can be reduced. The object of this research is where the position of the maximum brake temperature occurs? How to measure brake temperature is more practical? What sensor is optimal in detecting a brake temperature? The research method is carried out in a systematic stage that ends with an experimental method. This study indicates that the maximum temperature is relative to the entire friction area between the canvas and the drum brake. The most efficient sensor placement is in the hole in the drum brake cover so that installation is more practical and the brakes are not disturbed by the sensor’s presence. The optimal sensor is a thermocouple sensor because it is more stable to vibrations and more resistant to mud disturbances than infrared sensors. When using a thermocouple sensor, the temperature detection results must be corrected. The correction factor can be made with the equation y=10.3670+1.3205x–0.0003x2, where y is the actual temperature displayed, and x is the input temperature from the thermocouple sensor’s initial detection. Accurate brake temperature detection results will be developed as a signal for detecting brake faults in real-time to avoid brake failure. Finally, the safety of public transportation can be improved
References
- Suhariyanto (2019). Land Transportation Statistics 2018. BPS-Statistics Indonesia. Jakarta, 84. Available at: https://www.bps.go.id/publication/download.html?nrbvfeve=N2ZkZDMzNzkxMDhiNGE2MGUwNDZmNGM4&xzmn=aHR0cHM6Ly93d3cuYnBzLmdvLmlkL3B1YmxpY2F0aW9uLzIwMTkvMTEvMjcvN2ZkZDMzNzkxMDhiNGE2MGUwNDZmNGM4L3N0YXRpc3Rpay10cmFuc3BvcnRhc2ktLWRhcmF0LS0yMDE4Lmh0bWw%3D&twoadfnoarfeauf=MjAyMS0wMS0yNyAxOTowMDo1Ng%3D%3D
- Hasil investigasi KNKT di Ciloto, Bawen, Karangloso dan Kebumen (2017). Jakarta. Available at: http://knkt.dephub.go.id/knkt/ntsc_home/Publication/FGD%2021122017/5.%20Paparan%20Kasubkom%20LLAJ-FGD%20211217%20v%204%20Kecelakaan.pdf
- Owusu-Ansah, P., Alhassan, T., Frimpong, A., Agyei Agyemang, A. (2014). Survey of the Causes of Brake Failure in Commercial Mini-buses in Kumasi. Research Journal of Applied Sciences, Engineering and Technology, 7 (23), 4877–4882. doi: https://doi.org/10.19026/rjaset.7.878
- Chandra Verma, P., Menapace, L., Bonfanti, A., Ciudin, R., Gialanella, S., Straffelini, G. (2015). Braking pad-disc system: Wear mechanisms and formation of wear fragments. Wear, 322-323, 251–258. doi: https://doi.org/10.1016/j.wear.2014.11.019
- Oduro, S. (2012). Brake failure and its effect on road traffic accident in Kumasi Metropolis, Ghana. International Journal of Science and Technology, 1 (9), 448–454. Available at: https://www.researchgate.net/publication/279843241_Brake_Failure_and_its_Effect_on_Road_Traffic_Accident_in_Kumasi_Metropolis_Ghana
- Ahmed, I., Sofan, H., Abdelwahed, K., Fatouh, Y., Allam, E. M. (2019). Effect of Changing Drum Brakes Lining Form on the Brake Performance. International Research Journal of Engineering and Technology (IRJET), 06 (02). Available at: https://www.irjet.net/archives/V6/i2/IRJET-V6I201.pdf
- Awe, S. A. (2019). Developing Material Requirements for Automotive Brake Disc. Modern Concepts in Material Science, 2 (2). Available at: https://irispublishers.com/mcms/pdf/MCMS.MS.ID.000531.pdf
- Hemchi, T. (2008). Thermal stress and Thermal expansion in a brake drum of heavy commercial truck. Universiti Teknologi Petronas. Available at: http://utpedia.utp.edu.my/1001/1/THAWEESAK_HEMCHI.pdf
- Yan, M., Xu, J. (2018). Prediction Model for Brake-Drum Temperature of Large Trucks on Consecutive Mountain Downgrade Routes Based on Energy Conservation Law. Mathematical Problems in Engineering, 2018, 1–10. doi: https://doi.org/10.1155/2018/4587673
- Stephens, A. (2006). Aerodynamic Cooling of Automotive Disc Brakes. School of Aerospace, Mechanical & Manufacturing Engineering RMIT University, 15–20. Available at: https://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.1012.5236&rep=rep1&type=pdf
- Neis, P. D., Kruze, G., Ferreira, N. (2010). Relation between the temperature of the disc measured with thermocouple and by thermography using a reduced scale dynamometer. ABCM Symposium Series in Mechatronics, 4, 907–913. Available at: https://abcm.org.br/symposium-series/SSM_Vol4/Section_VII_SENSORS_AND_ACTUATORS/SSM4_VII_16.pdf
- Cho, H., Cho, C., Kim, C.-B. (2007). Thermal and Mechanical Performance Analysis in Accordance with Disk Stiffness Changes in Automotive Disk Brake. SAE Technical Paper Series. doi: https://doi.org/10.4271/2007-01-3661
- Husaini, M., Krishnan, P., Yaacob, S. (2018). Data Analysis for Braking System in Time Domain for Fault Diagnosis. International Research Journal of Engineering and Technology (IRJET), 05 (08), 348–354. Available at: https://www.irjet.net/archives/V5/i8/IRJET-V5I862.pdf
- Jegadeeshwaran, R., Sugumaran, V. (2015). Health monitoring of a hydraulic brake system using nested dichotomy classifier – A machine learning approach. International Journal of Prognostics and Health Management, 6 (1). Available at: https://www.phmsociety.org/sites/phmsociety.org/files/phm_submission/2014/ijphm_15_014.pdf
- Jegadeeshwaran, R., Sugumaran, V. (2015). Brake fault diagnosis using Clonal Selection Classification Algorithm (CSCA) – A statistical learning approach. Engineering Science and Technology, an International Journal, 18 (1), 14–23. doi: https://doi.org/10.1016/j.jestch.2014.08.001
- Giyarto (2018). Implementasi perangkat sensor suhu tromol mobil tangki di tbbm plumpang. Jakarta.
- Air Brake Performance and Wear Test Code Commercial Vehicle Inertia Dynamometer (2006). SAE International. doi: https://doi.org/10.4271/j2115_200608
- Surface vehicle recommended practice. SAE International. Available at: https://www.sae.org/standardsdev/tsb/tsb004.pdf
- ISO/PAS 12158:2002. Road vehicles – Braking systems – Temperature measuring methods. Available at: https://www.iso.org/standard/33466.html
- Adams, F. (2004). Pat. No. US 2005/0212357 A1. Brake monitoring and sensor system for sensing temperature and wear. No. 10/806,686; declareted: 23.03.2004; published: 29.09.2005. Available at: https://patents.google.com/patent/US20050212357A1/en
- Ghazaly, N. M., Makrahy, M. (2014). Experimental investigation of drum brake performance for passenger car. International Journal of Mechanical And Production Engineering, 2 (12), 70–73. Available at: http://www.iraj.in/journal/journal_file/journal_pdf/2-100-141760734370-73.pdf
- Adhitya, M., Siregar, R., Sumarsono, D. A., Nazaruddin, N., Heryana, G., Prasetyo, S., Zainuri, F. (2020). Experimental analysis in the test rig to detect temperature at the surface disc brake rotor using rubbing thermocouple. Eastern-European Journal of Enterprise Technologies, 2 (5 (104)), 6–11. doi: https://doi.org/10.15587/1729-4061.2020.191949
- Day, A. (2014). Braking of Road Vehicles. Butterworth-Heinemann, 488. doi: https://doi.org/10.1016/c2011-0-07386-6
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Rolan Siregar, Mohammad Adhitya, Danardono A Sumarsono, Nazaruddin Nazaruddin, Ghany Heryana, Sonki Prasetya, Fuad Zainuri
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.