Effect of multiphase structure of plasma coatings on their elastic and strength properties

Authors

  • Viacheslav Kopylov National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" Peremogy ave., 37, Kyiv, Ukraine, 03056, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2016.79586

Keywords:

plasma coating, modulus of elasticity, internal friction, crack resistance, strength, multiphase structure

Abstract

We examined physical and mechanical  characteristics of multiphase plasma coatings of lamellar structure, which include nanocomponents based on silicon dioxide. Elastic and strength properties of composite materials are explored, connected with peculiarities of the formation of structure and composition of coatings at plasma spraying, based on the proposed calculation–experimental technique, as well as with using results of measurements of internal friction and testing of compositions for the three–point bend. The work presents results of evaluation of the parameters of crack resistance and character of destruction of composite materials, based on examination of energy balance of the system "base – plasma coating" at the moment of crack initiation at exfoliation and cracking of coatings. We obtained values of intensity of stresses K1c of different systems and for the appropriate regions – in the grain body, on the border between the particles, in the area of interphase zone. The parameters of crack resistance (G1c, K1c) are calculated of the coating itself at its exfoliation and / or destruction.

We applied the corresponding techniques for determining cohesive strength for some cases of the crack propagation in the coating of dispersed structure depending on the composition of coating and ratio of modules of elasticity of the components of the given composition. The parameters of crack resistance are compared to physical and mechanical characteristics of plasma coatings – their adhesive and cohesive strength. The values of intensity of the released energy and coefficients of intensity of stresses at exfoliation or cracking are compared to such properties as adhesive and cohesive strength of the considered coatings. 

Author Biography

Viacheslav Kopylov, National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" Peremogy ave., 37, Kyiv, Ukraine, 03056

Doctor of Technical Sciences, Professor

Department of surface engineering

References

  1. Barvinok, V. A., Bogdanovich, V. A. (2012). Physical and mathematical modeling of processes of formation mesostructure-ordered plasma coatings. Journal technical physics, 82 (2), 105–112.
  2. Morks, M. F., Tsunekawa, Y., Okumiya, M., Shoeib, M. A. (2003). Splat Microstructure of Plasma Sprayed Cast Iron With Different Chamber Pressures. Journal of Thermal Spray Technology, 12 (2), 282–289. doi: 10.1361/105996303770348393
  3. Li, C.-J., Wang, W.-Z., He, Y. (2004). Dependency of fracture toughness of plasma sprayed Al2O3 coatings on lamellar structure. Journal of Thermal Spray Technology, 13 (3), 425–431. doi: 10.1361/10599630419364
  4. Tillmann, W., Nebel, J. (2010). Analysis of the Mechanical Properties of an Arc Sprayed WC-FeCSiMn Coating: Compression, Bending, and Tension Behavior. Journal of Thermal Spray Technology, 20 (1-2), 317–327. doi: 10.1007/s11666-010-9567-z
  5. Kopylov, V. I., Antonenko, D. A. (2014). Physical-mechanical properties and internal friction of multiphase materials with plasma coatings. Engineering problems, 2, 72–89.
  6. Li, H., Khor, K. A., Cheang, P. (2002). Young’s modulus and fracture toughness determination of high velocity oxy-fuel-sprayed bioceramic coatings. Surface and Coatings Technology, 155, 21–32. doi: 10.1016/s0257-8972(02)00026-9
  7. Brantner, H. P., Pippan, R., Prantl, W. (2003). Local and Global Fracture Toughness of a Flame Sprayed Molybdenum Coating. Journal of Thermal Spray Technology, 12 (4), 560–571. doi: 10.1361/105996303772082314
  8. Golovin, J. I. (2008). Nanoindentation and mechanical properties of solid bodies in submicrometer, thin surface layers and films (Review). Solid state Physics, 50 (12), 2113–2142.
  9. Bashta, A. V. (2012). Mechanical strength of the surface layers of the structural ceramics. Visnyk of NTU "HTU", 48 (954), 15–24.
  10. Dolgov, A. N. (2004). The method of determining the elastic modulus of thermal spray coatings. Powder metallurgy, 7/8, 110–115.
  11. Wu, D. J., Mao, W. G., Zhou, Y. C., Lu, C. (2011). Digital image correlation approach to cracking and decohesion in a brittle coating/ductile substrate system. Applied Surface Science, 257 (14), 6040–6043. doi: 10.1016/j.apsusc.2011.01.119
  12. Yamazaki, Y., Schmidt, A., Scholz, A. (2006). The determination of the delamination resistance in thermal barrier coating system by four-point bending tests. Surface and Coatings Technology, 201 (3-4), 744–754. doi: 10.1016/j.surfcoat.2005.12.023
  13. Bao, Y. W., Zhou, Y. C., Bu, X. X., Qiu, Y. (2007). Evaluating elastic modulus and strength of hard coatings by relative method. Materials Science and Engineering: A, 458 (1-2), 268–274. doi: 10.1016/j.msea.2006.12.131
  14. Dolgov, N. A., Chihira, I. V., Stuchliak, P. D., Buketov I. B. (2010). Using the criterion of adhesion-cohesin runano during flexion to create coatings with the best combination of strength characteristics. Oil and gas industry, 6, 41–45.
  15. Ivanchenko A. V., Dolgov, N. A., Besov, A. V., Chernyi, A. V. (2015). Peculiarities of adhesive-cohesive fracture plazminoguena coatings. Bulletin of the KhNTU, 3 (54), 126–132.
  16. Yu, L., Ma, Y., Zhou, C., Xu, H. (2005). Damping efficiency of the coating structure. International Journal of Solids and Structures, 42 (11-12), 3045–3058. doi: 10.1016/j.ijsolstr.2004.10.033
  17. Kopylov, V. I., Smirnov, I. V., Rybakov, S. V. (2005). Influence of composition and microstructure of oxide ceramic coatings on physico-mechanical properties of composite materials. Engineering problems, 2, 3–19.
  18. Kopylov, V. I., Varvus, I. A., Strongin, B. G. (1991). Main features of the formation of multi-component thermal spray coatings determining the physical and mechanical properties of the compositions during deposition. Phys.-Khim. mechanics of materials, 1, 65–70.
  19. Kopylov, V. I., Revo, S. L., Smirnov, I. V., Ivanenko, E. A., Lozovy, F. V., Antonenko, D. A. (2010). Influence of plasma coatings of powders with nano-size components on the internal friction of iron. Nanosistemy, nanomaterials, nanotechnology, 8 (1), 209–215.
  20. Kopylov, V. I., Smirnov, I. V., Dolgov N. A. (2004). The Use of failure criteria to assess the strength properties of thermal spray coatings. Engineering problems, 4, 3–11.
  21. Fastow, J. K. (1963).The determination of internal friction damping coatings. Izv. An SSSR, OTN, Mechanics and mechanical engineering, 3, 127–128.
  22. Hu, M. S., Evans, A. G. (1989). The cracking and decohesion of thin films on ductile substrates. Acta Metallurgica, 37 (3), 917–925. doi: 10.1016/0001-6160(89)90018-7
  23. Kopylov, V. I. (1999). Optimization of obtaining solid compositions based on the combination of technological and operational parameters of plasma spraying. Problems of strength, 1, 68–75.
  24. Rebinder, P. A., Shchukin, E. D., Margolis L. Y. (1964). On the mechanical strength of porous disperse bodies. Reports of as USSR, 154 (3), 695–698.
  25. Maksimovich, G. G., Shatinsky, V. F., Kopylov, V. I. (1983). Physico-chemical processes in plasma spraying and the destruction of materials with coatings. Kyiv: Naukova Dumka, 264.
  26. Chernoivanov, V. I., Karakozov, E. S. (1984). Physical-chemical processes of formation of the compounds during the deposition of powder materials. Statement of the problem. Welding production, 1, 2–5.

Downloads

Published

2016-10-30

How to Cite

Kopylov, V. (2016). Effect of multiphase structure of plasma coatings on their elastic and strength properties. Eastern-European Journal of Enterprise Technologies, 5(5 (83), 49–57. https://doi.org/10.15587/1729-4061.2016.79586

Issue

Vol. 5 No. 5 (83) (2016): Applied physics. Materials Science

Section

Materials Science

License

Copyright (c) 2016 Viacheslav Kopylov

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.