The conditions of improvement of productivity and quality of treatment at grinding

Authors

  • F. V. Novikov Simon Kuznets Kharkiv National University of Economics, Kharkiv, Ukraine
  • I. V. Gershikov Azov Machine Building Plant, Berdyansk, Ukraine
  • V. O. Andіlahay State higher educational establishment "Priazovskyi state technical university", Mariupol, Ukraine

DOI:

https://doi.org/10.31498/2225-6733.24.2012.19820

Keywords:

grinding, processing performance, the temperature of grinding

Abstract

Optimization of the parameters of grinding mode was carried out, including the number of circular disk’s passes, according to the criterion of the smallest treatment time for a piece, with regard to limitation in temperature factor. It was established that the parameters of multi-pass grinding treatment significantly limited the value of the auxiliary processing time spent on reversing the machine table, and single-part processing time, depending on the number of passes of the circle takes the extreme (minimum) value. Thus the main treatment time at the point of extremum was twice bigger than auxiliary processing time

Author Biographies

F. V. Novikov, Simon Kuznets Kharkiv National University of Economics, Kharkiv

Доктор технічних наук, професор

I. V. Gershikov, Azov Machine Building Plant, Berdyansk

Генеральний директор

V. O. Andіlahay, State higher educational establishment "Priazovskyi state technical university", Mariupol

Кандидат технічних наук, старший викладач

References

Якимов А.В. Оптимизация процесса шлифования / А.В. Якимов. – М. : Машиностроение, 1975. – 175 с.

Резников А.Н. Теплофизика процессов механической обработки материалов / А.Н. Резников. – М. : Машиностроение, 1981. – 279 с.

Сипайлов В.А. Тепловые процессы при шлифовании и управление качеством поверхности / В.А. Сипайлов. – М. : Машиностроение, 1978. – 166 с.

Силин С.С. Метод подобия при резании материалов / С.С. Силин. – М. : Машиностроение, 1979. – 152 с.

Теоретические основы резания и шлифования материалов: учеб. пособие / А.В. Якимов, Ф.В. Новиков, Г.В. Новиков, Б.С. Серов, А.А. Якимов. – Одесса : ОГПУ, 1999. – 450 с.

Новиков Ф.В. Оптимизация параметров режима шлифования зубчатых колес / Ф.В. Новиков, В.В. Нежебовский // Защита металлургических машин от поломок. – Мариуполь, 2010. – Вып.12. – С.56-62.

Downloads

How to Cite

Novikov, F. V., Gershikov, I. V., & Andіlahay V. O. (2013). The conditions of improvement of productivity and quality of treatment at grinding. Reporter of the Priazovskyi State Technical University. Section: Technical Sciences, (24), 248–252. https://doi.org/10.31498/2225-6733.24.2012.19820

Issue

No. 24 (2012): Reporter of the Priazovskyi State Technical University. Section: Technical sciences

Section

Mechanical engineering and metal working

License

The journal «Reporter of the Priazovskyi State Technical University. Section: Technical sciences» is published under the CC BY license (Attribution License).

This license allows for the distribution, editing, modification, and use of the work as a basis for derivative works, even for commercial purposes, provided that proper attribution is given. It is the most flexible of all available licenses and is recommended for maximum dissemination and use of non-restricted materials.

Authors who publish in this journal agree to the following terms:

1. Authors retain the copyright of their work and grant the journal the right of first publication under the terms of the Creative Commons Attribution License (CC BY). This license allows others to freely distribute the published work, provided that proper attribution is given to the original authors and the first publication of the work in this journal is acknowledged.

2. Authors are allowed to enter into separate, additional agreements for non-exclusive distribution of the work in the same form as published in this journal (e.g., depositing it in an institutional repository or including it in a monograph), provided that a reference to the first publication in this journal is maintained.