Increasing the arc burning stability during electric arc surfacing using ribbon electrode
DOI:
https://doi.org/10.31498/2225-6733.37.2018.160254Keywords:
power supply, inverter, converter, surfacing, ribbon electrode, stability, welding arcAbstract
The issues of stability of the arc during surfacing with a ribbon electrode are considered. It is shown that the electric arc movement along the end of the electrode is not progressive, but chaotic. In this case, the surfacing process is accompanied by periodic short circuits of the ribbon electrode on the workpiece. It was established experimentally that in order to improve the quality of the deposited metal, it is necessary to provide an operating mode with minimal fluctuations of the arc current. To solve this problem, it is necessary to realize the possibility of rapid destruction of the jumper, which is formed when the electrode is shorted on the workpiece, and to ensure reliable re-excitation of the electric arc. Regarding this, it is is proposed a method and a system for improving arc stability during arc surfacing with a ribbon electrode, consisting of an inverter with a microcontroller control, matching high-frequency power transformer, the secondary winding of which is connected through a capacitor in parallel to the welding arc. When a short circuit is detected between electrode and the workpiece (by catching the reduction of the voltage on the arc gap), the generator is turned on at the resonant frequency of the circuit formed by the capacitor and the inductance of the secondary circuit. A high-frequency component with an amplitude of several kA is superimposed on the main operating current, which leads to rapid heating and destruction of the jumper. The destruction is detected by the control system by «seeing» the increase of voltage on the arc gap. After that, the generator is turned off until the next short circuit is detectedReferences
Список використаних джерел (ГОСТ):
Кравцов Т.Г. Электродуговая наплавка электродной лентой / Т.Г. Кравцов. – М. : Машиностроение, 1978. – 168 с.
Гулаков С.В. Наплавка под флюсом ленточным электродом / С.В. Гулаков, В.Н. Мат-виенко, Б.И. Носовский. – Мариуполь : ПГТУ, 2006. – 136 с.
Размышляев А.Д. Автоматическая электродуговая наплавка ленточным электродом под флюсом / А.Д. Размышляев. – Мариуполь : ГВУЗ «ПГТУ», 2013. – 180 с.
Eichhorn F. Grundlagen des Lichtbogen Auftragschweißen mit Bandelektrode unter Schutcgas / F. Eichhorn, G. Lohrmann // Schweissen und Schneiden. – 1969. – Vol. 21, № 8. – Рр. 311-315.
Gert H. Modernes Unterpulver-Auftragschweissen mit Bandelektroden / H. Gert // BBC Nachrichten. – 1969. – № 9. – Рр. 537-539.
Гулаков С.В. Вдосконалення технології наплавлення стрічковим електродом / С.В. Гулаков, В.В. Бурлака, А.І. Міроненко // Вісник Приазовського державного технічного університету : Зб. наук. пр. / ДВНЗ «ПДТУ». – Маріуполь, 2017. – Вип. 34. – С. 94-97. – (Серія: Технічні науки).
Гулаков С.В. Применение источников питания с возрастающей внешней вольт-амперной характеристикой для широкослойной дуговой наплавки / С.В. Гулаков, В.Н. Матвиенко, Б.И. Носовский // Сварочное производство. – 1986. – № 5. – С. 14-15.
References:
Kravtsov T.G. Elektrodugovaia naplavka elektrodnoi lentoi [Electric arc surfacing with electrode tape]. Moscow, Mashinostroenie Publ., 1978. 168 p. (Rus.)
Gulakov S.V., Matvienko V.N., Nosovskii B.I. Naplavka pod fliusom lentochnym elektrodom [Surfacing with flux tape electrode]. Mariupol, SHEE «PSTU» Publ., 2006. 136 p. (Rus.)
Razmyshliaev A.D. Avtomaticheskaia elektrodugovaia naplavka lentochnym elektrodom pod fliusom [Automatic arc welding surfacing with a ribbon electrode]. Mariupol, SHEE «PSTU» Publ., 2013. 180 p. (Rus.)
Eichhorn F., Lohrmann G. Grundlagen des Lichtbogen Auftragschweißen mit Bandelektrode unter Schutcgas. Schweissen und Schneiden, vol. 21, no. 8, pp. 311-315. (Germ.)
Gert H. Modernes Unterpulver – Auftragschweissen mit Bandelektroden. BBC Nachrichten, 1969, no. 9, pp. 537-539. (Germ.)
Gulakov S.V., Burlaka V.V., Mironenko A.I. Vdoskonalennya tekhnolohiyi naplavlennya strichkoviym elektrodom [Improvement of electroplating technology by tape electrode]. Vіsnik Priazovs'kogo derzhavnogo tehnіchnogo unіversitetu. Serіia: Tekhnіchnі nauki – Reporter of the Priazovskyi State Technical University. Section: Technical Sciences, 2017, vol. 34, pp. 94-97. (Ukr.)
Gulakov S.V., Matviyenko V.N., Nosovskiy B.I. Primeneniye istochnikov pitaniya s vozras-tayushchey vneshney vol't-ampernoy kharakteristikoy dlya shirokosloynoy dugovoy naplavki [Use of power supplies with increasing external current-voltage characteristic for wide-layer arc surfacing]. Svarochnoe proizvodstvo – Welding production, 1986, vol. 5, pp. 14-15. (Rus.)
Downloads
Published
How to Cite
Issue
Section
License
The journal «Reporter of the Priazovskyi State Technical University. Section: Technical sciences» is published under the CC BY license (Attribution License).
This license allows for the distribution, editing, modification, and use of the work as a basis for derivative works, even for commercial purposes, provided that proper attribution is given. It is the most flexible of all available licenses and is recommended for maximum dissemination and use of non-restricted materials.
Authors who publish in this journal agree to the following terms:
1. Authors retain the copyright of their work and grant the journal the right of first publication under the terms of the Creative Commons Attribution License (CC BY). This license allows others to freely distribute the published work, provided that proper attribution is given to the original authors and the first publication of the work in this journal is acknowledged.
2. Authors are allowed to enter into separate, additional agreements for non-exclusive distribution of the work in the same form as published in this journal (e.g., depositing it in an institutional repository or including it in a monograph), provided that a reference to the first publication in this journal is maintained.
