A support of metrological traceability of inductance measurements in Ukraine

Authors

  • Oleh Velychko State Enterprise “All-Ukrainian State Scientific and Production Centre for Standardization, Metrology, Certification and Protection of Consumer” (SE “Ukrmetrteststandard”) Metrolohychna str., 4, Kyiv, Ukraine, 03143, Ukraine https://orcid.org/0000-0002-6564-4144
  • Sergii Shevkun State Enterprise “All-Ukrainian State Scientific and Production Centre for Standardization, Metrology, Certification and Protection of Consumer” (SE “Ukrmetrteststandard”) Metrolohychna str., 4, Kyiv, Ukraine, 03143, Ukraine https://orcid.org/0000-0003-1923-6227

DOI:

https://doi.org/10.15587/1729-4061.2017.109750

Keywords:

comparison of standards, metrological traceability, inductance, national metrology institute

Abstract

The comparative analysis of the results of the RMO international supplementary comparison of national standards of the units of inductance is conducted with the aim of evaluation of convergence. For the comparison, the reference values with the expanded uncertainties are calculated and the degrees of equivalence of standards of participants and expanded uncertainties for the nominal values of measures of 10 mH and 100 mH on a frequency of 1 kHz are determined. Metrological traceability of the national standard of every participant of comparisons to the units of the International system of units SI is determined.

For verification of consistency of the results of comparisons, the values of the χ2 criterion for the results of comparisons of standards of participants taking into account the measurement uncertainty are calculated. The obtained values of the criterion of consistency for the participants can be considered consistent, which is the objective confirmation of the measurement uncertainties declared by the participants.

The evaluation of calibration and measurement capabilities of Ukraine for the unit of inductance is realized. The methodology of evaluation of measurement uncertainty in a wide range of inductance values (from 10 µH to 100 H) is proposed. The results of the calculations of the values of measurement uncertainties according to the proposed methodology revealed that the results correspond to the data published in the international key comparison database for Ukraine in the range of capacitance values from 10 µH to 10 H on a frequency of 1 kHz

Author Biographies

Oleh Velychko, State Enterprise “All-Ukrainian State Scientific and Production Centre for Standardization, Metrology, Certification and Protection of Consumer” (SE “Ukrmetrteststandard”) Metrolohychna str., 4, Kyiv, Ukraine, 03143

Doctor of Technical Sciences, Professor, Director

Scientific and Production Institute of Electromagnetic Measurements

Sergii Shevkun, State Enterprise “All-Ukrainian State Scientific and Production Centre for Standardization, Metrology, Certification and Protection of Consumer” (SE “Ukrmetrteststandard”) Metrolohychna str., 4, Kyiv, Ukraine, 03143

PhD, Head of Department

Department of state standards of electromagnetic quantity, time and frequency

References

  1. Text of the CIPM MRA. Available at: http://www.bipm.org/en/cipm-mra/cipm-mra-text/
  2. Measurement comparisons in the context of the CIPM MRA. CIPM MRA-D-05:2013. Available at: http://www.bipm.org/utils/common/documents/CIPM-MRA/CIPM-MRA-D-05.pdf
  3. The BIPM key comparison database (KCDB). Available at: http://kcdb.bipm.org/
  4. JCGM 200:2012. International vocabulary of metrology. Basic and general concepts and associated terms (VIM 3-rd edition). Available at: http://www.bipm.org/utils/common/documents/jcgm/JCGM_200_2012.pdf
  5. Velichko, O. N. (2009). Traceability of measurement results at different levels of metrological work. Measurement Techniques, 52 (11), 1242–1248. doi: 10.1007/s11018-010-9428-7
  6. Uncertainty of measurement. Part 3: Guide to the expression of uncertainty in measurement (GUM). JCGM 100:2008. Available at: http://www.bipm.org/en/publications/guides/gum.html/
  7. Calibration and Measurement Capabilities in the context of the CIPM MRA. CIPM MRA-D-04:2013. Available at: http://www.bipm.org/en/cipm-mra/cipm-mra-documents/
  8. Velichko, O. N. (2010). Calibration and measurement capabilities of metrological institutes: features of preparation, examination, and publication. Measurement Techniques, 53 (6), 721–726. doi: 10.1007/s11018-010-9567-x
  9. Velychko, O., Gordiyenko, T. (2010). The implementation of general international guides and standards on regional level in the field of metrology. Journal of Physics: Conference Series, 238, 012044. doi: 10.1088/1742-6596/238/1/012044
  10. CООМЕТ R/GM/14:2016. Available at: http://www.coomet.org/DB/isapi/cmt_docs/2016/5/2BMD1O.pdf
  11. CООМЕТ R/GM/19:2016. Available at: http://www.coomet.org/DB/isapi/cmt_docs/2016/5/21XQGO.pdf
  12. Cox, M. G. (2002). The evaluation of key comparison data. Metrologia, 39 (6), 589–595. doi: 10.1088/0026-1394/39/6/10
  13. Cox, M. G. (2007). The evaluation of key comparison data: determining the largest consistent subset. Metrologia, 44 (3), 187–200. doi: 10.1088/0026-1394/44/3/005
  14. Mana, G., Massa, E., Predescu, M. (2012). Model selection in the average of inconsistent data: an analysis of the measured Planck-constant values. Metrologia, 49 (4), 492–500. doi: 10.1088/0026-1394/49/4/492
  15. Eckardt, H. (2001). International Comparison of 10 mH Inductance Standards at 1 kHz. CCEM-K3. Final Report. CCEM WGKC/2001-15. PTB, 35.
  16. Kölling, A. (2011). Final report on EUROMET comparison EUROMET.EM-K3: a 10 mH inductance standard at 1 kHz. Metrologia, 48 (1A), 01008–01008. doi: 10.1088/0026-1394/48/1a/01008
  17. Callegaro, L. (2007). EUROMET.EM-S20: Intercomparison of a 100 mH inductance standard (Euromet Project 607). Metrologia, 44 (1A), 01002–01002. doi: 10.1088/0026-1394/44/1a/01002
  18. Dierikx, E., Nestor, A., Melcher, J., Kölling, A., Callegaro, L. (2011). Final report on the supplementary comparison EURAMET.EM-S26: inductance measurements of 100 mH at 1 kHz (EURAMET project 816). Metrologia, 49 (1A), 01002–01002. doi: 10.1088/0026-1394/49/1a/01002
  19. Moreno, J. A., Côté, M., Koffman, A., Castro, B. I., Vasconcellos, R. de B. e, Kyriazis, G. et. al. (2016). SIM.EM-K3 Key comparison of 10 mH inductance standards at 1 kHz. Metrologia, 53 (1A), 01002–01002. doi: 10.1088/0026-1394/53/1a/01002
  20. Velychko, O., Shevkun, S. (2016). Final report on COOMET supplementary comparison of inductance at 10 mH and 100 mH at 1 kHz (COOMET.EM-S14). Metrologia, 53 (1A), 01009–01009. doi: 10.1088/0026-1394/53/1a/01009
  21. Velychko, O., Shevkun, S. (2017). Support of metrological traceability of capacitance measurements in Ukraine. Eastern-European Journal of Enterprise Technologies, 3 (9 (87)), 4–10. doi: 10.15587/1729-4061.2017.101897
  22. Shevkun, S., Surdu, M., Velichko, O. (2011). Evaluation of uncertainty of inductance measures on state primary standard of the unit of inductance. 18th TC4 IMEKO Symposium and IX International Congress on Electrical Metrology «Metrologia-2011». At Natal, 168–171.

Downloads

Published

2017-10-19

How to Cite

Velychko, O., & Shevkun, S. (2017). A support of metrological traceability of inductance measurements in Ukraine. Eastern-European Journal of Enterprise Technologies, 5(9 (89), 12–18. https://doi.org/10.15587/1729-4061.2017.109750

Issue

Vol. 5 No. 9 (89) (2017): Information and controlling system

Section

Information and controlling system

License

Copyright (c) 2017 Oleh Velychko, Sergii Shevkun

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.