Measurement of accuracy of grinding of nonrigid details with curvilinear generatrix
DOI:
https://doi.org/10.15587/1729-4061.2013.12380Keywords:
Accuracy, grinding, non-rigid parts, curved generator, measurement errorAbstract
Experimentally proved that the measurement of non-rigid machine components by contacts methods of measurements give erroneous results due to the interaction force to the part, which defined by the deformation process of this force.
This problem is very important for measurement of accuracy mandrels of cold-rolling pipe (CRP) machine on special grinding machine. This is especially important for mandrels of small diameters and large length. The use of additional support on the grinding machine does not allow for measurement the parameters of beats. So for the full measurement cycle in a single pass need use to alternative approaches to accounting for measurement error.
It is proposed to use algorithm correction using dependencies, which eliminates measurement errors during processingReferences
- Taranenko, W. Technologia kształtowania części maszyn o małej sztywności [Текст] : монография. / W. Taranenko, A. Świć; Wydawnictwo Politechniki Lubelskiej, Lublin 2005.- 282 p.
- Draczow, O. Technologia modułowa wytwarzania osiowosymetrycznych wałów długowymiarowych [Текст] / O. Draczow, W. Taranenko// ZESZYTY NAUKOWE Politechniki Rzeszowskiej NR 230 MECHANIKA, z. 67 - MODUŁOWE TECHNOLOGIE I KONSTRUKCJE W BUDOWE MASZYN, Rzeszow 2006. – p. 47 – 50.
- Taranenko, W. Urządzenia sterujące dokładnością obróbki części maszyn o małej sztywności [Текст] : монография. / W. Taranenko, A. Świć; Wydawnictwo Politechniki Lubelskiej, Lublin 2006.- 186 p.
- ГОСТ 30987-2003. Назначение размеров и допусков для нежестких деталей. [Текст] . - Введ. 2005-01-01. - М. : Изд-во стандартов, 2005. – 8 с.
- ISO 10579:2010. Geometrical product specification (GPS). Dimensioning and tolerancing. Non-rigid parts [Текст] . - Введ. 2011-01-01. - International Organization for Standardization, 2011. – 7 p.
- Strehlau, O. Introducing cold pilger mill technology [Текст] / O. Strehlau // The Tube and Pipe Journal, July 2006.
- Stapleton, G. Cold Pilger Technology [Текст] / G Stapleton. Fma Store, 2011.
- Incremental test leads firms HEIDENHAIN [Электронный ресурс] / HEIDENHAIN. – Режим доступа : WWW/ URL: / - www.heidenhain.de.
- Catalog HEIDENHAIN LENGTH GAUGES, 2013.
- Петраков, Ю.В. Автоматичне управління процесами обробки матеріалів різанням [Текст] / Ю.В Петраков. – УкрНДІАТ, Київ, 2004.-383 с.
- Петраков, Ю.В. Теорія автоматичного управління у металообробці [Текст] / Ю.В Петраков.– К., ІЗМН, 1988.-212 с.
- Taranenko, V., Swica, A. (2005) Technology development of machines with low rigidity. Publisher University of Lublin, Lublin. - 282 p.
- Drachov, O., Taranenko, V. (2006) Modular production technology axisymmetric long. Scientific Papers of the Rzeszów University of Technology, No 230 MECHANICS, z 67 - MODULAR TECHNOLOGIES AND CONSTRUCTION In mechanical engineering. - 47–50 p.
- Taranenko, V., Swica, A. (2006) Controls machining precision machine parts with low rigidity. Publisher University of Lublin, Lublin.- 186 p.
- GOST 30987-2003. Dimensioning and tolerancing for non-rigid parts. Moscow: Publishing House of Standards, 2005. – 8 p.
- ISO 10579:2010. Geometrical product specification (GPS). Dimensioning and tolerancing. Non-rigid parts. International Organization for Standardization, 2011. – 7 p.
- Strehlau, O. (2006) Introducing cold pilger mill technology. The Tube and Pipe Journal, July 2006.
- Stapleton, G. (2011) Cold Pilger Technology. Fma Store.
- Incremental test leads firms HEIDENHAIN / www.heidenhain.de.
- Catalog HEIDENHAIN LENGTH GAUGES, 2013.
- Petrakov, Y. (2004) Automatic management of material handling cutting. UkrNIIAT, Kyiv.-383 p.
- Petrakov, Y. (1988) Theory of automatic control in metalworking. K. IZMN.-212 p.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2014 Юрій Володимирович Петраков, Костянтин Михайлович Паньків, Сергій Миколайович Чамата
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.
