Influence of a material and the technological factors on improvement of operating properties of machine parts by reliefs and film coatings

Authors

  • Eduard Posviatenko National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010, Ukraine https://orcid.org/0000-0001-6606-1365
  • Nataliia Posviatenko National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010, Ukraine https://orcid.org/0000-0002-2217-4170
  • Ruslan Budyak Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008, Ukraine https://orcid.org/0000-0002-3633-7583
  • Ludmila Shvets Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008, Ukraine https://orcid.org/0000-0002-4364-0126
  • Yurii Paladiichuk Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008, Ukraine https://orcid.org/0000-0003-4257-9383
  • Petro Aksom National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010, Ukraine
  • Ilya Rybak National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010, Ukraine
  • Bogdan Sabadash Khmelnytskyi National University Instytuts’ka str., 11, Khmelnytskyi, Ukraine, 29016, Ukraine
  • Valentyn Hryhoryshen Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008, Ukraine https://orcid.org/0000-0002-1112-3044

DOI:

https://doi.org/10.15587/1729-4061.2018.142924

Keywords:

operational properties, rolling bearings, austenitic steels, regular reliefs, deep openings

Abstract

A joint effect of preliminary cold plastic deformation and environmentally friendly lubricating substances of plant origin on the improvement of machinability of austenitic steels was considered. This extends the use of such steels as structural material in machine building. The influence of micro- and macroreliefs of machined parts both as technological and operational factors was explored. The former involves division of allowances during machining deep openings, and the latter involves the improvement of operational characteristics of the surface of a part. The influence of film coatings on an increase in durability of rolling bearings was studied. In particular, it was found that these coatings heal micro cracks from grinding of rolling bearings cases and bodies and increase the reliability of these crucial parts by increasing the level of hardness. It was shown that the curvature of the generatrix of deep openings should be decreased by changing the directions of major movements in the related operations. It was established that special attention should be paid to the heredity of machining.

The ways of improvement of machinability of austenitic steels were substantiated. This is the use of preliminary cold plastic deformation to execute a part of work of cutting and transferring paramagnetic status of steels into magnetic. It is also the use of environmentally friendly lubricants of plant origin during cutting. The dual purpose of the reliefs of the surface of a part – technological and operational – was established. The former is executed by a special broaching tool and is effective during machining deep openings. The purpose of the latter is to create labyrinths for lubricants and division of shells into separate elements. The mechanism of the action of vacuum film coating on reliability of rolling bearings, which contributes to healing micro cracks from the preliminary abrasive treatment and an increase in surface hardness, was studied. It was shown that a decrease in the height of curvilinearity and waviness of deep openings is achieved by the change in the main motion of the related operations.

Results of the research are the basis for creating technologies of critical machine parts in production

Author Biographies

Eduard Posviatenko, National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010

Doctor of Technical Sciences, Professor

Department of production, repair and materials science

Nataliia Posviatenko, National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010

PhD, Associate Professor

Department of Road Building Machines

Ruslan Budyak, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

PhD

Department of operation of the machine and tractor fleet and technical service

Ludmila Shvets, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

PhD, Associate Professor

Department of operation of the machine and tractor fleet and technical service

Yurii Paladiichuk, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

PhD, Associate Professor

Department of operation of the machine and tractor fleet and technical service

Petro Aksom, National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010

Postgraduate student

Department of Manufacturing, Repairing and Materials Science

Ilya Rybak, National Transport University Omelianovicha-Pavlenka str., 1, Kyiv, Ukraine, 01010

Postgraduate student

Department of Manufacturing, Repairing and Materials Science

Bogdan Sabadash, Khmelnytskyi National University Instytuts’ka str., 11, Khmelnytskyi, Ukraine, 29016

Postgraduate student

Department of durability and reliability of machines

Valentyn Hryhoryshen, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

Assistant

Department of operation of machine-tractor park and technical service

References

  1. DSTU 2860:1994. Reliability of technology. Terms and definitions (1995). Kyiv: Gosstandart of Ukraine, 26.
  2. Tkachuk, N. A., Dyachenko, S. S., Posvyatenko, E. K. et. al. (2018). Continuous and discrete-continual modification of parts surfaces. Kharkiv: Planet-Print, 259.
  3. ISO14577–3:2015. Metallic materials. Instrumented indentation test for hardness and materials parameters. Part 3: Calibration of reference blocks (2015). Geneva, ISO Publ, 8.
  4. Trent, E. M. (1984). Metal Cutting. Elsevier, 254. doi: https://doi.org/10.1016/c2013-0-00966-8
  5. Enahoro, H. E. (1966). Effekt of cold – working on chip formation in metal cutting. Ann. C.S.R.P., 13, 251–261.
  6. Wagner, H. D., Lourie, O., Zhou, X. F. (1999). Macrofragmentation and microfragmentation phenomena in composite materials. Composites Part A: Applied Science and Manufacturing, 30 (1), 59–66. doi: https://doi.org/10.1016/s1359-835x(98)00072-4
  7. Oliver, W. C., Pharr, G. M. (2004). Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. Journal of Materials Research, 19 (1), 3–20. doi: https://doi.org/10.1557/jmr.2004.0002
  8. Marchenko, А., Tkachuk, M., Sobol, O. et. al. (2017). Innovative technologies of composite strengthening of elements surfaces for defense and energy industries products. Mechanics and machine building, 1, 234–246. Available at: http://repository.kpi.kharkov.ua/bitstream/KhPI-Press/33143/1/MM_2017_1_Marchenko_Innovatsiini.pdf
  9. Chatterjee-Fisher, R., Eisel, F. V., Hofmann, R. et. al.; Supov, A. V. (Ed.) (1990). Nitriding and carbonitriding. Moscow: Metallurgy, 280.
  10. Falub, C. V., Karimi, A., Ante, M., Kalss, W. (2007). Interdependence between stress and texture in arc evaporated Ti–Al–N thin films. Surface and Coatings Technology, 201 (12), 5891–5898. doi: https://doi.org/10.1016/j.surfcoat.2006.10.046
  11. Stout, K. Y., Dong, W. P., Mainsah, E. (1993). A Proposol for Standardisation of Asserment of Three–Dimensional Mikro-Topography-Part 1: Snrface Digitisation and Parametric Characterisation. Birmingham: The University of Birmingham, 21.
  12. Chen, X., Chen, G. (2009). On the thermally induced cracking of a segmented coating deposited on the outer surface of a hollow cylinder. Surface and Coatings Technology, 203 (9), 1114–1120. doi: https://doi.org/10.1016/j.surfcoat.2008.10.002

Downloads

Published

2018-09-24

How to Cite

Posviatenko, E., Posviatenko, N., Budyak, R., Shvets, L., Paladiichuk, Y., Aksom, P., Rybak, I., Sabadash, B., & Hryhoryshen, V. (2018). Influence of a material and the technological factors on improvement of operating properties of machine parts by reliefs and film coatings. Eastern-European Journal of Enterprise Technologies, 5(12 (95), 48–56. https://doi.org/10.15587/1729-4061.2018.142924

Issue

Section

Materials Science