Construction of a force method for estimating the longitudinal stability of the process of thin sheet rolling
DOI:
https://doi.org/10.15587/1729-4061.2019.160487Keywords:
balance of forces, sheet rolling, deformation site, gripping capacity, stability criterionAbstract
We have analyzed theoretical features of rolls gripping capacity at simple rolling process under a steady mode. It is shown that depending on the conditions for deformation the ratio of the maximum gripping angle to a friction coefficient can be equal to, be less or more than 2.
An experimental study has been performed involving the rolling of lead stepped samples measuring the forward creep at each step. Results of the experiment demonstrate that in the extreme case of deformation the forward creep is greater than zero, that is, there is a sufficient reserve of frictional forces so that reduction can be further increased, however, it is impossible.
We have analyzed the balance of all horizontal forces at deformation site. It is shown that at each cross section the stretching horizontal contact forces are used not only to overcome the ejecting ones, but also to compensate for the longitudinal internal forces that occur as a result of plastic deformation of a metal.
A force method for estimating the longitudinal stability of the sheet rolling process has been developed. An indicator of stability is a criterion that is determined from the diagrams of distribution of a normal contact stress and the stress of friction. It is shown that at a positive value of the criterion the rolling process proceeds under a steady mode; at a negative value, the stable process is impossible; and in the case it equals zero, the limit deformation occurs.
A theoretical study has been conducted into determining the maximum gripping angle under different conditions of sheet rolling. It is shown that the ratio of the maximum gripping angle to a friction coefficient almost does not depend on a strip thickness, the diameter of rolls, as well as friction coefficient, and equals 1.43‒1.44. A decrease in the gripping capacity of rolls is explained by the effect, at a deformation site, not only of contact forces, but the internal forces as well.
References
- Grudev, A. P. (1998). Zahvatyvayushchaya sposobnost' prokatnyh valkov. Moscow: “SP Intermet Inzhiniring”, 283.
- Maksimenko, O. P., Romanyuk, R. Ya. (2010). Estimation of Rolling Process Stability by Contact-Stress Diagrams. Metallurgical and Mining Industry, 2 (2), 122–129.
- Vasylev, Ya. D., Minaiev, O. A. (2009). Teoriya pozdovzhnoi prokatky. Donetsk: UNITEKh, 488.
- Romaniuk, R. Ya. (2014). Analiz metodiv otsinky pozdovzhnoi stiykosti protsesu tonkolystovoi prokatky. Obrabotka materyalov davlenyem, 1, 173–177.
- Mazur, V. L. et. al. (1997). Upravlenie kachestvom tonkolistovogo prokata. Kyiv: Tekhnika, 384.
- Garber, Е. А., Pavlov, S. I., Kozhevnikova, I. A., Timofeeva, M. A., Kuznetsov, V. V. (2010). Steel sheet surface quality improvement on the basis of new solutions in cold rolling theory. Vestnik Cherepoveckogo gosudarstvennogo universiteta, 2, 116–125.
- Garber, E. A. et. al. (2010). Issledovanie nestabil'nosti poperechnogo profilya polos na nepreryvnyh shirokopolosnyh stanah goryachey prokatki. Proizvodstvo prokata, 2, 2–7.
- Garber, E. A. et. al. (2010). Stabilizaciya tekhnologicheskih rezhimov shirokopolosnyh stanov dlya uluchsheniya kachestva poperechnogo profilya goryachekatanyh polos. Stal', 8, 56–61.
- Garber, E. A., Bolobanova, N. L. (2012). Modelirovanie uprugih deformaciy v valkah kletey i opredelenie ih konstruktivnyh parametrov, obespechivayushchih povyshenie tochnosti holodnokatanyh polos. Proizvodstvo prokata, 1, 17–18.
- Prihod'ko, I. Yu. et. al. (2009). Sistema avtomaticheskogo regulirovaniya ploskostnosti polos s ispol'zovaniem beskontaktnyh metodov izmereniya ploskostnosti i temperatury. Stal', 3, 41–45.
- Abdelkhalek, S., Montmitonnet, P., Legrand, N., Buessler, P. (2011). Coupled approach for flatness prediction in cold rolling of thin strip. International Journal of Mechanical Sciences, 53 (9), 661–675. doi: https://doi.org/10.1016/j.ijmecsci.2011.04.001
- Li, G.-H. (2018). EVC-Plus technique of transverse thickness deviation control of non-oriented silicon steel during cold rolling. IRON AND STEEL, 53 (8), 68–72. doi: https://doi.org/10.13228/j.boyuan.issn0449-749x.20180174
- Ji, J. (2015). Stability of the coupled vibrations of work roll and strip in cold rolling process. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 231 (7), 1169–1181. doi: https://doi.org/10.1177/0954405415585376
- Niroomand, M. R., Forouzan, M. R., Salimi, M., Shojaei, H. (2012). Experimental Investigations and ALE Finite Element Method Analysis of Chatter in Cold Strip Rolling. ISIJ International, 52 (12), 2245–2253. doi: https://doi.org/10.2355/isijinternational.52.2245
- Ren, Z., Xiao, H., Yu, C., Wang, J. (2017). Experimental study on transverse displacement of the metal during cold thin strip rolling. Procedia Engineering, 207, 1326–1331. doi: https://doi.org/10.1016/j.proeng.2017.10.891
- Kozhevnikov, A., Kozhevnikova, I., Bolobanova, N. (2018). Dynamic model of cold strip rolling. Metalurgija, 57 (1-2), 99–102.
- Romaniuk, R. Ya., Levchuk, K. O. (2017). Osoblyvosti sylovoi vzaiemodiyi shtaby z valkamy pry tonkolystoviy prokattsi. Zbirnyk naukovykh prats Dniprovskoho derzhavnoho tekhnichnoho universytetu (tekhnichni nauky), 2 (31), 51–55.
- Osakada, K. (2010). History of plasticity and metal forming analysis. Journal of Materials Processing Technology, 210 (11), 1436–1454. doi: https://doi.org/10.1016/j.jmatprotec.2010.04.001
- Vasilev, Ya. D. et. al. (2013). Opredelenie neytral'nogo ugla pri holodnoy prokatke s ispol'zovaniem utochnennoy modeli napryazheniy treniya. Obrabotka metallov davleniem, 3 (36), 81–85.
- Romaniuk, R. Ya. (2014). Stalist protsesu prokatky na osnovi doslidnykh epiur kontaktnykh napruzhen. Zbirnyk naukovykh prats Dniprodzerzhynskoho derzhavnoho tekhnichnoho universytetu. Tekhnichni nauky, 1 (24), 32–38.
- Romaniuk, R. Y., Levchuk, K. O., Hasylo, Y. A. (2017). Forecasting of theoretical orthographic epures of contact voltages at thin sheet rolling. Bulletin of National Technical University "KhPI": coll. sci. papers. Ser.: Innovative technologies and equipment handling materials in mechanical engineering and metallurgy, 37, 71–76.
- Maksimenko, O. P., Kachan, O. O. (2016). Vliyanie rezul'tiruyushchey prodol'nyh sil na ugol neytral'nogo secheniya. Zbirnyk naukovykh prats Dniprodzerzhynskoho derzhavnoho tekhnichnoho universytetu. Tekhnichni nauky, 2 (29), 38–42.
- Vasilyev, Y. D. (2012). Theoretical study of the infl uence of tension on the energy effi ciency of cold-rolled strip. Izvestiya Visshikh Uchebnykh Zavedenii. Chernaya Metallurgiya = Izvestiya. Ferrous Metallurgy, 55 (6), 3–5. doi: https://doi.org/10.17073/0368-0797-2012-6-3-5
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Roman Romaniuk, Kateryna Levchuk, Yurii Hasylo, Dmitry Chasov, Olha Kriukovska
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.
