Solution of the problem of the theory of elasticity and analysis of the stress state of a fibrous composite layer under the action of transverse compressive forces

Authors

DOI:

https://doi.org/10.15587/1729-4061.2022.263460

Keywords:

layer with cylindrical inclusions, fibrous composite, addition theorems, reduction method

Abstract

An analytical-numerical solution of the spatial problem of elasticity theory for a composite in the form of a layer with two longitudinal endless continuous cylindrical inclusions is proposed. Homogeneous, isotropic materials of the layer and inclusions differ from each other in the modulus of elasticity and Poisson's ratio. Normal stresses are set on the upper and lower boundaries of the layer. The object of study is the stress state of such a composite. The problem is the lack of a high-precision method for calculating multiply connected bodies of this type. The solution of the problem is based on the generalized Fourier method for the Lame equations in various coordinate systems. The problem is reduced to an infinite system of linear algebraic equations, which is solved by the reduction method. In a numerical study, the stress state was obtained inside the composite bodies, within their conjugations, and on the isthmus between inclusions. It has been established that extreme stresses sρ=–0.9306 MPa, sf=–0.5595 MPa, tρf=–0.315 MPa occur on the mating face. Analysis of the stress state indicates the need to take into account the normal stresses on the mating surface. This is due to the presence of a binder, which may differ in physical characteristics from the main components of the composite. The results have logical physical correctness and, in simplified versions, are fully consistent with the results of similar problems from other approved sources. In the work, the transition formulas in the basic solutions between different coordinate systems, the conjugation conditions for different bodies, and the strict fulfillment of the equilibrium conditions for given boundary functions are simultaneously applied. This made it possible to obtain a high-precision solution of a new problem in the theory of elasticity for a layer with cylindrical inclusions and given only stresses on the boundary surfaces. The proposed method of calculation can be applied in the design of structures made of fibrous composites in the aircraft industry and construction.

Author Biographies

Vitaly Miroshnikov, National Aerospace University “Kharkiv Aviation Institute”

Doctor of Technical Sciences, Associate Professor, Head of Department

Department of Aircraft Strength

Oleksandr Savin, National Aerospace University “Kharkiv Aviation Institute”

PhD, Associate Professor

Department of Aircraft Strength

Basheer Younis, National Aerospace University “Kharkiv Aviation Institute”

PhD, Associate Professor

Department of Aircraft Strength

Vyacheslav Nikichanov, National Aerospace University “Kharkiv Aviation Institute”

PhD, Associate Professor

Department of Aircraft Production Technology

References

  1. Balabai, R. M., Zdeshchyts, A. V. (2018). Nanocellulose as the Main Composite Component of Electromechanical Sensors. Ukrainian Journal of Physics, 63 (9), 828. doi: https://doi.org/10.15407/ujpe63.9.828
  2. Aitharaju, V., Aashat, S., Kia, H., Satyanarayana, A., Bogert, P. (2016). Progressive damage modeling of notched composites. NASA Technical Reports Server. Available at: https://ntrs.nasa.gov/citations/20160012242
  3. Streng, G., Fiks, Dzh. (1977). Teoriya metoda konechnykh elementov. Moscow: Mir, 352.
  4. Daschenko, A. F., Lazareva, D. V., Sur'yaninov, N. G. (2007). ANSYS v zadachakh inzhenernoy mekhaniki. Odessa: Astroprint, 484.
  5. Khoroshun, L. P., Nazarenko, L. V. (2014). Nonlinear Deformation Properties of Composites with Transversely Isotropic Components. International Applied Mechanics, 50 (3), 253–262. doi: https://doi.org/10.1007/s10778-014-0628-8
  6. Fallahi, H., Taheri-Behrooz, F., Asadi, A. (2019). Nonlinear Mechanical Response of Polymer Matrix Composites: A Review. Polymer Reviews, 60 (1), 42–85. doi: https://doi.org/10.1080/15583724.2019.1656236
  7. Taheri-Behrooz, F., Bakhshan, H. (2016). Characteristic length determination of notched woven composites. Advanced Composite Materials, 27 (1), 67–83. doi: https://doi.org/10.1080/09243046.2016.1232007
  8. Taheri-Behrooz, F., Bakhshi, N. (2016). Neuber’s rule accounting for the material nonlinearity influence on the stress concentration of the laminated composites. Journal of Reinforced Plastics and Composites, 36 (3), 214–225. doi: https://doi.org/10.1177/0731684416680302
  9. Bakhshi, N., Taheri-Behrooz, F. (2019). Length effect on the stress concentration factor of a perforated orthotropic composite plate under in-plane loading. Composite Materials and Engineering, 1 (1), 71–90. Available at: http://www.techno-press.org/content/?page=article&journal=cme&volume=1&num=1&ordernum=5
  10. Ugrimov, S., Smetankina, N., Kravchenko, O., Yareshchenko, V. (2021). Analysis of Laminated Composites Subjected to Impact. Integrated Computer Technologies in Mechanical Engineering - 2020, 234–246. doi: https://doi.org/10.1007/978-3-030-66717-7_19
  11. Rodichev, Y. M., Smetankina, N. V., Shupikov, O. M., Ugrimov, S. V. (2018). Stress-Strain Assessment for Laminated Aircraft Cockpit Windows at Static and Dynamic Loads. Strength of Materials, 50 (6), 868–873. doi: https://doi.org/10.1007/s11223-019-00033-4
  12. Smetankina, N., Ugrimov, S., Kravchenko, I., Ivchenko, D. (2019). Simulating the Process of a Bird Striking a Rigid Target. Advances in Design, Simulation and Manufacturing II, 711–721. doi: https://doi.org/10.1007/978-3-030-22365-6_71
  13. Smetankina, N., Kravchenko, I., Merculov, V., Ivchenko, D., Malykhina, A. (2020). Modelling of Bird Strike on an Aircraft Glazing. Advances in Intelligent Systems and Computing, 289–297. doi: https://doi.org/10.1007/978-3-030-37618-5_25
  14. Ghasemi, A. R., Razavian, I. (2012). Measurement of Variation in Fracture Strength and Calculation of Stress Concentration Factor in Composite Laminates with Circular Hole. Journal of Solid Mechanics, 4 (3), 226–236. Available at: https://jsm.arak.iau.ir/article_514479_509c3e00525d93de836d940c48099af8.pdf
  15. Jafari, M., Bayati Chaleshtari, M. H., Ardalani, E. (2018). Determination of Optimal Parameters for Finite Plates with a Quasi-Square Hole. Journal of Solid Mechanics, 10 (2). 300–314. Available at: https://www.sid.ir/en/Journal/ViewPaper.aspx?ID=594415
  16. Dastjerdi, Sh., Yazdanparast, L. (2018). New Method for Large Deflection Analysis of an Elliptic Plate Weakened by an Eccentric Circular Hole. Journal of Solid Mechanics, 10 (3). 561–570. Available at: https://jsm.arak.iau.ir/article_544403.html
  17. Abolghasemi, S., Eipakchi, H. R., Shariati, M. (2018). Investigation of Pre-buckling Stress Effect on Buckling Load Determination of Finite Rectangular Plates with Circular Cutout. Journal of Solid Mechanics, 10 (4), 816–830. Available at: https://jsm.arak.iau.ir/article_545721.html
  18. Guz', A. N., Kubenko, V. D., Cherevko, M. A. (1978). Difraktsiya uprugikh voln. Kyiv: Nauk. dumka, 308.
  19. Grinchenko, V. T., Meleshko, V. V. (1981). Garmonicheskie kolebaniya i volny v uprugikh telakh. Kyiv: Nauk. Dumka, 284.
  20. Grinchenko, V. T., Ulitko, A. F. (1968). An exact solution of the problem of stress distribution close to a circular hole in an elastic layer. Soviet Applied Mechanics, 4 (10), 31–37. doi: https://doi.org/10.1007/bf00886618
  21. Volchkov, Vit. V., Vukolov, D. S., Storozhev, V. I. (2016). Diffraction of shear waves on internal tunnel cylindrical inhomogeneities in the form of a cavity and inclusion in the elastic layer with free face. Mekhanika tverdogo tela, 46, 119–133. Available at: http://dspace.nbuv.gov.ua/handle/123456789/123857
  22. Nikolaev, A. G., Protsenko, V. S. (2011). Obobschennyy metod Fur'e v prostranstvennykh zadachakh teorii uprugosti. Kharkiv: Nats. aerokosm. universitet im. N.E. Zhukovskogo «KhAI», 344.
  23. Ukrayinets, N., Murahovska, O., Prokhorova, O. (2021). Solving a one mixed problem in elasticity theory for half-space with a cylindrical cavity by the generalized Fourier method. Eastern-European Journal of Enterprise Technologies, 2 (7 (110)), 48–57. doi: https://doi.org/10.15587/1729-4061.2021.229428
  24. Nikolaev, O. G., Tanchik, E. A. (2016). Stresses in an Infinite Circular Cylinder with Four Cylindrical Cavities. Journal of Mathematical Sciences, 217 (3), 299–311. doi: https://doi.org/10.1007/s10958-016-2974-z
  25. Nikolaev, A. G., Tanchik, E. A. (2015). The first boundary-value problem of the elasticity theory for a cylinder with N cylindrical cavities. Numerical Analysis and Applications, 8 (2), 148–158. doi: https://doi.org/10.1134/s1995423915020068
  26. Nikolaev, A. G., Tanchik, E. A. (2016). Stresses in an elastic cylinder with cylindrical cavities forming a hexagonal structure. Journal of Applied Mechanics and Technical Physics, 57 (6), 1141–1149. doi: https://doi.org/10.1134/s0021894416060237
  27. Nikolaev, A. G., Tanchik, E. A. (2016). Model of the Stress State of a Unidirectional Composite with Cylindrical Fibers Forming a Tetragonal Structure. Mechanics of Composite Materials, 52 (2), 177–188. doi: https://doi.org/10.1007/s11029-016-9571-6
  28. Protsenko, V. S., Popova, N. A. (2004). Vtoraya osnovnaya kraevaya zadacha teorii uprugosti dlya poluprostranstva s krugovoy tsilindricheskoy polost'yu. Dop. NAN Ukrainy. Ser. Matematika, prirodoznavstvo, tekhn. nauki, 12, 52–58.
  29. Protsenko, V., Miroshnikov, V. (2018). Investigating a problem from the theory of elasticity for a half-space with cylindrical cavities for which boundary conditions of contact type are assigned. Eastern-European Journal of Enterprise Technologies, 4 (7 (94)), 43–50. doi: https://doi.org/10.15587/1729-4061.2018.139567
  30. Miroshnikov, V. (2019). The study of the second main problem of the theory of elasticity for a layer with a cylindrical cavity. Strength of Materials and Theory of Structures, 102, 77–90. doi: https://doi.org/10.32347/2410-2547.2019.102.77-90
  31. Miroshnikov, V., Denysova, T., Protsenko, V. (2019). The study of the first main problem of the theory of elasticity for a layer with a cylindrical cavity. Strength of Materials and Theory of Structures, 103, 208–218. doi: https://doi.org/10.32347/2410-2547.2019.103.208-218
  32. Miroshnikov, V. Y. (2020). Stress State of an Elastic Layer with a Cylindrical Cavity on a Rigid Foundation. International Applied Mechanics, 56 (3), 372–381. doi: https://doi.org/10.1007/s10778-020-01021-x
  33. Miroshnikov, V. Y. (2019). Investigation of the Stress State of a Composite in the Form of a Layer and a Half Space with a Longitudinal Cylindrical Cavity at Stresses Given on Boundary Surfaces. Journal of Mechanical Engineering, 22 (4), 24–31. doi: https://doi.org/10.15407/pmach2019.04.024
  34. Miroshnikov, V. Y., Medvedeva, A. V., Oleshkevich, S. V. (2019). Determination of the Stress State of the Layer with a Cylindrical Elastic Inclusion. Materials Science Forum, 968, 413–420. doi: https://doi.org/10.4028/www.scientific.net/msf.968.413
  35. Miroshnikov, V. (2019). Investigation of the Stress Strain State of the Layer with a Longitudinal Cylindrical Thick-Walled Tube and the Displacements Given at the Boundaries of the Layer. Journal of Mechanical Engineering, 22 (2), 44–52. doi: https://doi.org/10.15407/pmach2019.02.044

Downloads

Published

2022-08-30

How to Cite

Miroshnikov, V., Savin, O., Younis, B., & Nikichanov, V. (2022). Solution of the problem of the theory of elasticity and analysis of the stress state of a fibrous composite layer under the action of transverse compressive forces. Eastern-European Journal of Enterprise Technologies, 4(7 (118), 23–30. https://doi.org/10.15587/1729-4061.2022.263460

Issue

Vol. 4 No. 7 (118) (2022): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2022 Vitaly Miroshnikov, Oleksandr Savin, Basheer Younis, Vyacheslav Nikichanov

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.