Determining the residual service life of polymer-modified asphalt concrete pavement on road bridges

Authors

DOI:

https://doi.org/10.15587/1729-4061.2023.279006

Keywords:

highway, road bridge, residual resource, crack resistance, asphalt pavement, polymers

Abstract

The object of research is the asphalt pavement of road bridges. Its residual period was assessed taking into account the joint effect of the ambient temperature and vehicles.

It has been established that a set of negative factors affects the reduction of the service life (residual resource) of asphalt pavement on bridges. These include different modulus of elasticity of reinforced concrete base and asphalt pavement and the difference in coefficients of linear thermal expansion. As well as loads from the wheels of vehicles, temperature fluctuations, alternating freezing-thawing of water in pores and damaged places.

It was found that one of the reasons for reducing the residual life of asphalt pavement on reinforced concrete road bridges is the insufficient study and use of polymers in order to adjust the properties of asphalt concrete.

Taking into account the joint influence of temperature and transport in assessing the crack resistance of asphalt pavement on reinforced concrete road bridges would allow a more objective assessment of the residual life of such coatings and their service life. Arrangement of asphalt pavement with improved properties, due to polymeric latex, could increase its residual life. This, in turn, would lead to a reduction in costs for the repair and maintenance of not only asphalt pavement but also the road bridge as a whole

Author Biographies

Artur Onyshchenko, National Transport University

Doctor of Technical Sciences, Professor

Department of Bridges and Tunnels

Vitalii Kovalchuk, Lviv Polytechnic National University

Doctor of Technical Sciences, Associate Professor

Department of Railway Transport

Olexiy Zagorodniy, National Transport University

Department of Bridges and Tunnels

Vadym Moroz, National Transport University

Doctor of Technical Sciences, Professor

Department of Bridges and Tunnels

References

  1. DSTU 4044:2019. Viscous petroleum road bitumens. Specification (2019). Kyiv. Available at: http://online.budstandart.com/ua/catalog/doc-page.html?id_doc=84291
  2. DSTU 8959:2019. Asphalt concrete mixtures and asphalt concrete roads based on bitumes of modified polymers. Specifications (2019). Kyiv. Available at: http://online.budstandart.com/ua/catalog/doc-page.html?id_doc=86571
  3. Onyshchenko, A. M., Kuzminets, M. P., Nevinhlovskyi, V. F., Harkusha, M. V. (2015). Teoretychni ta praktychni doslidzhennia resursu asfaltobetonnoho pokryttia na zalizobetonnykh transportnykh sporudakh. Kyiv: NTU, 334.
  4. Zolotareva, V. A., Bratchun, V. I. (Eds.) (2003). Modified bituminous waters, special bitums and bitums with additives in a road construction. Movie Road Association. Technical Commate "Non-Roads" (C8). Kharkiv: Education Knife.
  5. DSTU 9116:2021. Bitumen and bituminous binders. Polymer modified road bitumen. Specification (2021). Kyiv. Available at: http://online.budstandart.com/ru/catalog/doc-page.html?id_doc=96264
  6. Onischenko, A., Aksenov, S., Nevynhlovskyy, V., Garkusha, M., Riznichenko, O. (2014). Method of preparation and test results of bitumen modified with polymers using laboratory blade mixer. Proceeding of the 17th Conference for Junior Researchers “Science – Future of Lithuania” Transport engineering and management. Vilnius, 41–44.
  7. Onyshchenko, A. M., Nevinhlovskyi, V. F., Harkusha, M. V. (2012). Pidvyshchennia zalyshkovoho resursu asfaltobetonnoho pokryttia za rakhunok polimernykh lateksiv na zalizobetonnykh mostovykh sporudakh. Naukovi notatky, 36, 227–232.
  8. Makarchev, O. O., Mozghovyi, V. V., Besarab, O. M., Onyshchenko, A. M. (2006). Otsinka vplyvu modyfikatora bitumu Butonal NS 198 na pidvyshchennia dovhovichnosti asfaltobetonnoho pokryttia. Dorohy i mosty, 5, 275–288.
  9. Sidun, I., Solodkyy, S., Vollis, O., Stanchak, S., Bidos, V. (2021). Adhesion of bituminous binders with aggregates in the context of surface dressing technology for road pavements treatment. Theory and Building Practice, 1, 92–99. doi: https://doi.org/10.23939/jtbp2021.01.092
  10. Luchko, Y. Y., Koval, P. M., Korniev, M. M., Lantukh-Liashchenko, A. I., Kharkhalis, M. R. (2005). Mosty: konstruktsiyi ta nadiynist. Lviv: Kameniar, 989.
  11. Barksdale, R. D. (1972). Laboratory Evaluation of Rutting in Base Course Materials. Third International Conference on the Structural Design of Asphalt Pavements, 1, 161–174. Available at: https://trid.trb.org/view/138844
  12. Stuart, K. D., Mogawer, W. S., Romero, P. (2000). Validation of asphalt binder and mixture tests that measure rutting. FHWA-RD-99-204. Available at: https://www.fhwa.dot.gov/publications/research/infrastructure/pavements/ppub/99204/index.cfm
  13. Materials testing manual / Department of Transport and Main Roads. Queensland Department of Transport and Main Roads. Available at: https://nla.gov.au/nla.obj-1744784729/view
  14. Zhou, F., Li, H., Chen, P., Scullion, T. (2014). Research Report No. FHWA/TX-14/0-6674-1: Laboratory Evaluation of Asphalt Binder Rutting, Fracture, and Adhesion tests. Available at: https://rosap.ntl.bts.gov/view/dot/27289
  15. Kovalchuk, V., Onyshchenko, A., Fedorenko, O., Habrel, M., Parneta, B., Voznyak, O. et al. (2021). A comprehensive procedure for estimating the stressed-strained state of a reinforced concrete bridge under the action of variable environmental temperatures. Eastern-European Journal of Enterprise Technologies, 2 (7 (110)), 23–30. doi: https://doi.org/10.15587/1729-4061.2021.228960
  16. Kovalchuk, V., Sobolevska, Y., Onyshchenko, A., Fedorenko, O., Tokin, O., Pavliv, A. et al. (2021). Procedure for determining the thermoelastic state of a reinforced concrete bridge beam strengthened with methyl methacrylate. Eastern-European Journal of Enterprise Technologies, 4 (7 (112)), 26–33. doi: https://doi.org/10.15587/1729-4061.2021.238440
  17. Vyrozhemskyi, V., Kopynets, I., Kischynskyi, S., Bidnenko, N. (2017). Epoxy asphalt concrete is a perspective material for the construction of roads. IOP Conference Series: Materials Science and Engineering, 236, 012022. doi: https://doi.org/10.1088/1757-899x/236/1/012022
  18. Mozgovyi, V., Baran, S., Kutsman, A. (2017). Improvement in strength calculation for pavement structure of rail station areas. MATEC Web of Conferences, 116, 01009. doi: https://doi.org/10.1051/matecconf/201711601009
  19. Gustelev, O. O., Gulyaev, V. I., Haydachuk, V. V., Mozgovy, V. V., Zayets, Yu. O., Shevchuk, L. V., Shlyun, N. V. (2018). Thermoelastic state of multilayer road surfaces. Kharkiv: NTU, 252.
  20. Gustelev, O. O., Haydaichuk, V. V., Mozgovy, V. V., Shevchuk, L. V. (2019). Deformation analysis road surface on the metal plate of the Southern Bridge. Industrial construction and engineering facilities: scientific and industrial magazine, 1, 31–38.
Determining the residual service life of polymer-modified asphalt concrete pavement on road bridges

Downloads

Published

2023-06-30

How to Cite

Onyshchenko, A., Kovalchuk, V., Zagorodniy, O., & Moroz, V. (2023). Determining the residual service life of polymer-modified asphalt concrete pavement on road bridges . Eastern-European Journal of Enterprise Technologies, 3(1 (123), 41–51. https://doi.org/10.15587/1729-4061.2023.279006

Issue

Vol. 3 No. 1 (123) (2023): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2023 Artur Onyshchenko, Vitalii Kovalchuk, Olexiy Zagorodniy, Vadym Moroz

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.