Development of a magnetic rotator to enhance the hydrogen evolution reaction in a proton exchange membrane water electrolysis cell

Authors

DOI:

https://doi.org/10.15587/1729-4061.2024.308944

Keywords:

magnetic rotator, green water electrolysis, hydrogen production, design optimization

Abstract

In this study, a large-scale magnetic rotator for hydrogen production boosting was designed. The study addresses the challenge of selecting and designing mechanical components for a dynamic magnetic field (DMF) magnetic rotator in a green hydrogen electrolysis power plant, focusing on ensuring component reliability and efficiency under operational stresses. The aim is to determine suitable machine element materials (shaft, clutch, gears, etc.), allowable shear stress, and interconnection mechanisms through theoretical and practical evaluations. The method includes calculating the allowable shear stress for the spline based on carbon steel tensile strength, applying safety factors for material properties and load considerations, and determining shaft diameter using torque and shock load factors. Standard catalogs guide the selection of interconnections like clutches, gears, and bearings to ensure compatibility and performance. The results indicate that a 95 mm diameter S30C carbon steel shaft, with an allowable shear stress of 7.8 kg/mm2, meets the design requirements. The chosen spline dimensions and a 12.5 MW, 14-pole induction motor align with the system’s needs, ensuring reliable operation. The discussion highlights the critical balance between theoretical predictions and practical application in design optimization. It underscores the importance of incorporating safety factors and verifying component suitability to ensure robust performance of the magnetic rotator. This study provides a comprehensive approach to design optimization, integrating theoretical analysis with practical considerations to achieve optimal performance and reliability. The design output of this study can be used to boost the hydrogen evolution reaction in the SIEMENS Sylizer 300 electrolysis cell.

Author Biographies

Purnami Purnami, Brawijaya University

Doctor of Engineering, Associate Professor

Department of Mechanical Engineering

Willy Satrio Nugroho, Brawijaya University

Doctor of Engineering, Assistant Professor

Department of Mechanical Engineering

Lukman Hakim, Brawijaya University

Doctor of Engineering, Associate Professor

Department of Chemistry

I Nyoman Gede Wardana, Brawijaya University

Doctor of Engineering, Professor

Department of Mechanical Engineering

References

  1. Handayani, K., Krozer, Y., Filatova, T. (2017). Trade-offs between electrification and climate change mitigation: An analysis of the Java-Bali power system in Indonesia. Applied Energy, 208, 1020–1037. https://doi.org/10.1016/j.apenergy.2017.09.048
  2. Arcos, J. M. M Santos, D. M. F. (2023). The Hydrogen Color Spectrum: Techno-Economic Analysis of the Available Technologies for Hydrogen Production. Gases, 3 (1), 25–46. https://doi.org/10.3390/gases3010002
  3. Incer-Valverde, J., Korayem, A., Tsatsaronis, G., Morosuk, T. (2023). “Colors” of hydrogen: Definitions and carbon intensity. Energy Conversion and Management, 291, 117294. https://doi.org/10.1016/j.enconman.2023.117294
  4. Energy Explained. The hydrogen colour spectrum. Available at: https://www.nationalgrid.com/stories/energy-explained/hydrogen-colour-spectrum
  5. Diab, J., Fulcheri, L., Hessel, V., Rohani, V., Frenklach, M. (2022). Why turquoise hydrogen will Be a game changer for the energy transition. International Journal of Hydrogen Energy, 47 (61), 25831–25848. https://doi.org/10.1016/j.ijhydene.2022.05.299
  6. Al-Douri, A., Groth, K. M. (2024). Hydrogen production via electrolysis: State-of-the-art and research needs in risk and reliability analysis. International Journal of Hydrogen Energy, 63, 775–785. https://doi.org/10.1016/j.ijhydene.2024.03.188
  7. Grigoriev, S. A., Fateev, V. N., Bessarabov, D. G., Millet, P. (2020). Current status, research trends, and challenges in water electrolysis science and technology. International Journal of Hydrogen Energy, 45 (49), 26036–26058. https://doi.org/10.1016/j.ijhydene.2020.03.109
  8. Schmitz, R., Brandes, J., Nolte, H., Kost, C., Lux, B., Haendel, M., Held, A. (2024). Implications of hydrogen import prices for the German energy system in a model-comparison experiment. International Journal of Hydrogen Energy, 63, 566–579. https://doi.org/10.1016/j.ijhydene.2024.03.210
  9. Zainal, B. S., Ker, P. J., Mohamed, H., Ong, H. C., Fattah, I. M. R., Rahman, S. M. A. et al. (2024). Recent advancement and assessment of green hydrogen production technologies. Renewable and Sustainable Energy Reviews, 189, 113941. https://doi.org/10.1016/j.rser.2023.113941
  10. Konyukhov, V. K. (2011). Spin states ofpara-water andortho-water molecule in gas and liquid phases. Physics and Chemistry of Liquids, 49 (3), 343–346. https://doi.org/10.1080/00319100903456154
  11. Chen, Y.-J., Li, Y.-H., Chen, C.-Y. (2022). Studying the Effect of Electrode Material and Magnetic Field on Hydrogen Production Efficiency. Magnetochemistry, 8 (5), 53. https://doi.org/10.3390/magnetochemistry8050053
  12. da Silva Falcão, B., Jeong, K., Al Ghafri, S., Robinson, N., Tang, L., Kozielski, K., Johns, M. L. (2024). Ortho- to para-hydrogen catalytic conversion kinetics. International Journal of Hydrogen Energy, 62, 345–351. https://doi.org/10.1016/j.ijhydene.2024.02.380
  13. Purnami, P., Winarto, W., Sofi’i, Y. K., Nugroho, W. S., Wardana, I. N. G. (2023). The enhancement of magnetic field assisted water electrolysis hydrogen production from the compact disc recordable waste polycarbonate layer. International Journal of Hydrogen Energy, 48 (48), 18154–18165. https://doi.org/10.1016/j.ijhydene.2023.01.329
  14. Purnami, P., Hamidi, N., Nur Sasongko, M., Siswanto, E., Widhiyanuriyawan, D., Pambudi Tama, I. et al. (2022). Enhancement of hydrogen production using dynamic magnetic field through water electrolysis. International Journal of Energy Research, 46 (6), 7309–7319. https://doi.org/10.1002/er.7638
  15. Purnami, P., Satrio Nugroho, W., Hamidi, N., W, W., Schulze, A. A., Wardana, I. N. G. (2024). Double deep Q network intelligent adaptive control for highly efficient dynamic magnetic field assisted water electrolysis. International Journal of Hydrogen Energy, 59, 457–464. https://doi.org/10.1016/j.ijhydene.2024.01.321
  16. Purnami, P., Satrio Nugroho, W., Sofi’i, Y. K., Wardana, I. N. G. (2024). The impact of sodium lauryl sulfate on hydrogen evolution reaction in water electrolysis. International Journal of Hydrogen Energy, 79, 1395–1405. https://doi.org/10.1016/j.ijhydene.2024.07.127
  17. Purnami, P., Willy Satrio, N., Sofi’i, Y. K., Wardana, I. N. G. (2024). The impact of mechanical vibration at cathode on hydrogen yields in water electrolysis. Journal of Power Sources, 615, 235075. https://doi.org/10.1016/j.jpowsour.2024.235075
  18. Handiwibowo, G. A., Nadlifatin, R., Bhawika, G. W., Noer, L. R. (2021). The Contribution of Absorptive Capacities to New Innovative Product Development Performance: A Conceptual Framework. International Journal of Mechanical Engineering Technologies and Applications, 2 (1), 73. https://doi.org/10.21776/mechta.2021.002.01.11
  19. Setyarini, P. H., Gapsari, F., Harjo, A. O. R. (2022). Surface Characterization on Electrophoretic Deposition Oof 316l Stainless Steel with Dissolved Chitosan for Biomedical Application. International Journal of Mechanical Engineering Technologies and Applications, 3 (1), 40. https://doi.org/10.21776/mechta.2022.003.01.6
  20. Juniansyah, G., Lathifah, S. M., Prajitno, D. H. (2021). Synthesis Polymer Matrix Composite Epoxy-FeNdB-Mn for Radar Absorbing Material Application. International Journal of Mechanical Engineering Technologies and Applications, 2 (1), 1. https://doi.org/10.21776/mechta.2021.002.01.1
  21. Akbar, D. H., Purnami, P., Budio, S. P. (2020). Influence of Surface Roughness and Paint Coating on Corrosion Rate. International Journal of Mechanical Engineering Technologies and Applications, 1 (1), 15. https://doi.org/10.21776/mechta.2020.001.01.3
  22. Habiby, M. N. A., Istianto, P. V., Fahmi, M. (2023). Optimization of cutting direction parameters for a cnc milling machining process pocket on structure and surface roughness on postep motorcycle spare parts. International Journal of Mechanical Engineering Technologies and Applications, 4 (2), 135–143. https://doi.org/10.21776/mechta.2023.004.02.3
  23. Widodo, T. D., Raharjo, R., Risonarta, V. Y., Bintarto, R., Kusumaningsih, H., Saputra, M. H. (2020). The Effect of Sand Blasting on Shear Stress of Fiberglass – Shorea spp. Composite. International Journal of Mechanical Engineering Technologies and Applications, 1 (1), 1. https://doi.org/10.21776/mechta.2020.001.01.1
  24. Anggamawarti, M. F., Alviari, L. P., Sanjiwani, Y., Risonarta, V. Y. (2020). Quality Analysis of 5.56 mm Ammunition Defect using Taguchi Method: A Review. International Journal of Mechanical Engineering Technologies and Applications, 1 (1), 29. https://doi.org/10.21776/mechta.2020.001.01.5
  25. Ihsan, M. A., Sumantri, Y., Irawan, Y. S. (2024). Integration of taguchi and promethee for cnc milling machining parameter optimization on AA6061. International Journal of Mechanical Engineering Technologies and Applications, 5 (1), 96–107. https://doi.org/10.21776/mechta.2024.005.01.10
  26. Flamm, B., Peter, C., Büchi, F. N., Lygeros, J. (2021). Electrolyzer modeling and real-time control for optimized production of hydrogen gas. Applied Energy, 281, 116031. https://doi.org/10.1016/j.apenergy.2020.116031
  27. Ravichandran, S., Venkatkarthick, R., Sankari, A., Vasudevan, S., Jonas Davidson, D., Sozhan, G. (2014). Platinum deposition on the nafion membrane by impregnation reduction using nonionic surfactant for water electrolysis – An alternate approach. Energy, 68, 148–151. https://doi.org/10.1016/j.energy.2014.02.077
  28. Xu, Y., Wang, C., Huang, Y., Fu, J. (2021). Recent advances in electrocatalysts for neutral and large-current-density water electrolysis. Nano Energy, 80, 105545. https://doi.org/10.1016/j.nanoen.2020.105545
  29. Peter, C., Vrettos, E., Büchi, F. N. (2022). Polymer electrolyte membrane electrolyzer and fuel cell system characterization for power system frequency control. International Journal of Electrical Power & Energy Systems, 141, 108121. https://doi.org/10.1016/j.ijepes.2022.108121
  30. Boichenko, S., Danilin, O., Shkilniuk, I., Yakovlieva, A., Khotian, A., Pavlovskyi, M. et al. (2023). Substantiating the expediency of using hydrogen fuel cells in electricity generation. Eastern-European Journal of Enterprise Technologies, 3 (8 (123)), 17–29. https://doi.org/10.15587/1729-4061.2023.280046
  31. Mustafa, F. F., Hussein, O., Fakhri, O. F., Sabri, A. H. (2020). Design and development of high-accuracy machine for wire bending. Eastern-European Journal of Enterprise Technologies, 5 (1 (107)), 29–35. https://doi.org/10.15587/1729-4061.2020.202184
  32. Lytvyn, V., Vysotska, V., Shatskykh, V., Kohut, I., Petruchenko, O., Dzyubyk, L. et al. (2019). Design of a recommendation system based on collaborative filtering and machine learning considering personal needs of the user. Eastern-European Journal of Enterprise Technologies, 4 (2 (100)), 6–28. https://doi.org/10.15587/1729-4061.2019.175507
  33. Kvasnikov, V., Kvashuk, D., Prygara, M., Legeta, J. (2023). Designing tools for assessing the reliability of electric motor torque measurements by using identifiers of anomalous deviations in a noisy signal system. Eastern-European Journal of Enterprise Technologies, 6 (5 (126)), 15–25. https://doi.org/10.15587/1729-4061.2023.292187
  34. Suga, K., Sularso (1997). Dasar Perencanaan dan Pemilihan Elemen Mesin. Jakarta: Pradnya Paramitha.
  35. Nanda, R. A., Karyadi, K., Roban, R., Dewadi, F. M. (2024). RPM measurement comparison using a thermometer and LM393 microcontroller. International Journal of Mechanical Engineering Technologies and Applications, 5 (1), 51–62. https://doi.org/10.21776/mechta.2024.005.01.6
  36. Kvasnikov, V., Kvashuk, D., Prygara, M., Shelukha, O., Molchanova, K. (2024). Devising a technique for measuring torque of electric motors using machine vision. Eastern-European Journal of Enterprise Technologies, 1 (5 (127)), 16–32. https://doi.org/10.15587/1729-4061.2024.298513
  37. Darmo, S., Soenoko, R., Siswanto, E., Widodo, T. D. (2019). The influence of the pack decarburizing process with Pinctada maxima shell powder agent on the properties of high carbon steel. Eastern-European Journal of Enterprise Technologies, 1 (12 (97)), 6–13. https://doi.org/10.15587/1729-4061.2019.153762
  38. Xu, H., Wang, P., Ma, H., He, D., Zhao, X., Yang, Y. (2022). Analysis of axial and overturning ultimate load-bearing capacities of deep groove ball bearings under combined loads and arbitrary rotation speed. Mechanism and Machine Theory, 169, 104665. https://doi.org/10.1016/j.mechmachtheory.2021.104665
  39. Huang, W., Tian, H., Ma, H., Wang, P., Yang, Y., Han, Q. (2023). An improved method for calculating the lateral and angular stiffness of spline couplings considering parallel misalignment. Mechanism and Machine Theory, 189, 105436. https://doi.org/10.1016/j.mechmachtheory.2023.105436
  40. Morozyuk, L., Hrudka, B., Yuzhakova, O. (2018). Selection of new working fluids for a heat-using compression refrigerating machine with the block «turbine- compressor». Eastern-European Journal of Enterprise Technologies, 5 (8 (95)), 33–40. https://doi.org/10.15587/1729-4061.2018.142061
  41. Yurianto, Y., Pratikto, P., Soenoko, R., Suprapto, W. (2019). Effect of quench and temper on hardness and wear of HRP steel (armor steel candidate). Eastern-European Journal of Enterprise Technologies, 3 (12 (99)), 55–61. https://doi.org/10.15587/1729-4061.2019.156799
  42. Rahman, A., Winarto, W., Siswanto, E. (2024). Optimization of shell and tube heat exchanger design with inclined baffles. International Journal of Mechanical Engineering Technologies and Applications, 5 (1), 63–72. https://doi.org/10.21776/mechta.2024.005.01.7
  43. Sugiono, S., Nugroho, W. S., Wiryawan, E., Oktavianty, O., Sulistyarini, D. H. (2023). Controlling the train car´s center of gravity (COG) position based on train load levelling. Journal of Applied Research and Technology, 21 (6), 1057–1065. https://doi.org/10.22201/icat.24486736e.2023.21.6.1977
  44. Quan, Z., Ge, L., Wei, Z., Li, Y. W., Quan, L. (2021). A Survey of Powertrain Technologies for Energy-Efficient Heavy-Duty Machinery. Proceedings of the IEEE, 109 (3), 279–308. https://doi.org/10.1109/jproc.2021.3051555
  45. de Souza, D. F., Salotti, F. A. M., Sauer, I. L., Tatizawa, H., de Almeida, A. T., Kanashiro, A. G. (2022). A Performance Evaluation of Three-Phase Induction Electric Motors between 1945 and 2020. Energies, 15 (6), 2002. https://doi.org/10.3390/en15062002
  46. Sutrisno, S., Soenoko, R., Irawan, Y. S., Widodo, T. D. (2021). Effect of coconut fiber treatment with limestone water media on the fiber surface, wettability, and interface shear strength. Eastern-European Journal of Enterprise Technologies, 1 (6 (109)), 48–56. https://doi.org/10.15587/1729-4061.2021.217730
  47. Taufik, A., Pratikto, P., Suprapto, A., Sonief, A. A. (2021). Analysis of the influence of hot rolled plate steel treatment using temper and quench-temper method on vickers hardness number enhancement. Eastern-European Journal of Enterprise Technologies, 4 (12 (112)), 18–24. https://doi.org/10.15587/1729-4061.2021.233349
  48. Soenoko, R., Purnami, Utami Dewi, F. G. (2017). Second stage cross flow turbine performance. ARPN Journal of Engineering and Applied Sciences, 12 (6). Available at: http://www.arpnjournals.org/jeas/research_papers/rp_2017/jeas_0317_5818.pdf
  49. Sugiarto, S., Soenoko, R., Purnowidodo, A., Irawan, Y. S. (2018). The effect of external magnetic flux field in the QTS weldment on the change of fatigue crack propagation behaviors. Eastern-European Journal of Enterprise Technologies, 2 (12 (92)), 4–11. https://doi.org/10.15587/1729-4061.2018.122919
  50. Sugiarto, Purnowidodo, A., Soenoko, R., Irawan, Y. S., Sonief, A. A. (2016). The use of magnetic flux to the welding of hot roll quench tempered steel. ARPN Journal of Engineering and Applied Sciences, 11 (2), 1061–1064. Available at: http://www.arpnjournals.org/jeas/research_papers/rp_2016/jeas_0116_3454.pdf
  51. Sugiarto, Dr., Ma’arif, Moch. S., Purwanto, H., Ery Mahendra, W. J., Oswari, H. (2023). Characteristic of friction stir welding weld joint of AA 6061 on initial temperature difference. MM Science Journal, 2023 (1). https://doi.org/10.17973/mmsj.2023_03_2022094
  52. Wijayanti, W., Sasongko, M. N., Purnami (2016). The calorific values of solid and liquid yields consequenced by temperatures of mahogany pyrolysis. ARPN Journal of Engineering and Applied Sciences, 11 (2), 917–921. Available at: http://www.arpnjournals.org/jeas/research_papers/rp_2016/jeas_0116_3427.pdf
  53. Sunardi, Choiron, Moch. A., Sugiarto, Setyarini, P. H. (2023). Development of fishing boat collision models in extreme weather using computer simulation. EUREKA: Physics and Engineering, 2, 149–159. https://doi.org/10.21303/2461-4262.2023.002601
  54. Sunardi, E. F., Choiron, M. A., Sugiarto, A. W. M., Setyarini, P. H., Nurwahyudi, A. (2024). Fishing Vessel Safety in Indonesia: A Study of Accident Characteristics and Prevention Strategies. International Journal of Safety and Security Engineering, 14 (2), 499–511. https://doi.org/10.18280/ijsse.140217
Development of a magnetic rotator to enhance the hydrogen evolution reaction in a proton exchange membrane water electrolysis cell

Downloads

Published

2024-10-25

How to Cite

Purnami, P., Nugroho, W. S., Hakim, L., & Wardana, I. N. G. (2024). Development of a magnetic rotator to enhance the hydrogen evolution reaction in a proton exchange membrane water electrolysis cell . Eastern-European Journal of Enterprise Technologies, 5(1 (131), 6–16. https://doi.org/10.15587/1729-4061.2024.308944

Issue

Vol. 5 No. 1 (131) (2024): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2024 Purnami Purnami, Willy Satrio Nugroho, Lukman Hakim, I Nyoman Gede Wardana

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.