Development of the sealing method of the pump clearance by well production

Authors

  • Рамиз Сейфулла Гурбанов Geotechnological Problems of Oil, Gas and Chemistry SRI 20 Azadlyg ave., Baku, Azerbaijan, AZ1010, Azerbaijan
  • Малейка Агамоглан Мамедова Azerbaijan State University of Oil and Industry 20 Azadlyg ave., Baku, Azerbaijan, AZ1010, Azerbaijan
  • Тюркан Гейдар Гурбанова Azerbaijan State University of Oil and Industry 20 Azadlyg ave., Baku, Azerbaijan, AZ1010, Azerbaijan

DOI:

https://doi.org/10.15587/1729-4061.2015.51958

Keywords:

plunger-cylinder, "fluid-fracture" effect, delivery rate of pump, leakage, clearance, hydroseal, right-hand thread

Abstract

The paper deals with the issues of creating sealing systems in process equipment. The problem of leakage through the clearance of the plunger-cylinder pair of the deep-well pump is considered, and well production is used as a sealing medium. To implement the specified sealing system, the "fluid-fracture" effect, developed by R. S. Gurbanov and M.A. Mamedova is used.

The "fluid-fracture" effect at certain critical values of fracture opening leads to changes in the rheological properties of the well production, which allows to identify the pumps with the necessary clearances for the production to work as a seal. The developed method allows to reduce the delivery rate of the pump and decrease the cost of pumps used in a single well.

Author Biographies

Рамиз Сейфулла Гурбанов, Geotechnological Problems of Oil, Gas and Chemistry SRI 20 Azadlyg ave., Baku, Azerbaijan, AZ1010

Doctor of Technical Sciences, Professor, Chief Researcher, Corresponding Member of ANAS

Малейка Агамоглан Мамедова, Azerbaijan State University of Oil and Industry 20 Azadlyg ave., Baku, Azerbaijan, AZ1010

PhD, Associate Professor

Тюркан Гейдар Гурбанова, Azerbaijan State University of Oil and Industry 20 Azadlyg ave., Baku, Azerbaijan, AZ1010

Postgraduate student, researcher

References

  1. Amelin, I. D., Andchiasov, R. S., Gimatudinov, Sh. K., Karateev, Ju. P., Levykin, E. V., Lutoshkin, G. S. (1978). Jekspluatacija i tehnologija razrabotki neftjanyh i gazovyh mestorozhdenii. Moscow: «Nedra», 353.
  2. Mirzadzhanzade, A. H., Gurbanov, R. S. et. al. (1986). Teorija i praktika primenenija glubinnyh nasosov s gidravlicheskim zatvorom. Moscow: «Nedra», 210.
  3. Amirov, A. D., Hasanov, A. M., Gurbanov, R. S. (1971). a. s. №32566. Rabochaja zhidkost' gidrozatvora.
  4. Kostychenko, E. V., Sulejmanov, T. S., Gurbanov, R. S. (1991). a. s. №1701981. Skvazhinnyj shtangovyj nasos.
  5. Gurbanov, R. S., Mamedova, M. A., Miriev, G. M. (1986). Metodicheskoe rukovodstvo po opredeleniju parametrov plastovyh sistem i jeffektivnosti primenenija polimernogo vozdejstvija v treshhinnyh kollektorah. Baku: AzNIPIneft', 35.
  6. Mamedova, M. A. (2007). Issledovanie dvizhenija neszhimaemoj vjazkoj zhidkosti v ploskoradial'noj mikrotreshhine. Azerbajdzhanskoe neftjanoe hozjajstvo, 11, 25–28.
  7. Gurbanov, R. S., Mamedova, M. A. (2015). Reologicheskie issledovanie vody v kanalah mikronnoj tolshhiny. ANH, 03, 23–28.
  8. Mamedova, M. A. (2010). Jeksperimental'noe issledovanie dvizhenija nen'jutonovskih zhidkostej v ploskoradial'noj mikrotreshhine. Nauchnoe obozrenie, 5, 51–57.
  9. Orkin, K. G., Kuchinskij, P. K. (1955). Fizika neftjanogo plaste. Gostoptehizdat, 299.
  10. Nabiev, N. A. (2010). Razrabotka i issledovanija tehnicheskih i tehnologicheskih faktorov, obespechivajushhih povyshenie jekspluatacionnyh pokazatelej skvazhinnyh shtangovyh nasosov. Baku, 189.

Downloads

Published

2015-10-28

How to Cite

Гурбанов, Р. С., Мамедова, М. А., & Гурбанова, Т. Г. (2015). Development of the sealing method of the pump clearance by well production. Eastern-European Journal of Enterprise Technologies, 5(1(77), 59–62. https://doi.org/10.15587/1729-4061.2015.51958

Issue

Vol. 5 No. 1(77) (2015): Mechanical engineering technology

Section

Mechanical engineering technology

License

Copyright (c) 2015 Рамиз Сейфулла Гурбанов, Малейка Агамоглан Мамедова, Тюркан Гейдар Гурбанова

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.