Investigation of the process of smoothing with ultrasound

Authors

DOI:

https://doi.org/10.15587/1729-4061.2018.131047

Keywords:

surface plastic deformation, ultrasonic smoothness, part, depth, feed, treatment speed

Abstract

We studied and simulated the ultrasonic smoothing process. We carried out the analysis of the contact interaction of a tool with a part in the process of ultrasonic smoothing with a preceding gap. The analysis provides an opportunity to calculate a change in a size of a part during the treatment depending on modes. We derived the dependences of a contact area at the ultrasonic smoothness with a preceding gap. We performed the experimental study of an influence of parameters of the process of ultrasonic smoothing on parameters of a quality of a surface layer of a part. We established that in order to ensure the required roughness and accuracy, the depth of introduction should not exceed 7 μm, especially when treated parts are made of materials with a low modulus of elasticity.

We developed an installation for experiments based on the high precision automatic screw machine 16B05АF10. All additional devices and tools were attached to the tool holder of a given machine.

We developed a technique to measure the time of contact between a tool and an article under ultrasonic smoothing with a preceding gap.

We established that deformation of micro roughnesses occurs due to a pressure of projections of micro roughnesses to cavities since we excluded shift deformation by using a solid lubricant. The fact that there was no texture on the microsection of the treated surface, although we could observe hardening of a surface, indicates that there is no shift deformation. Based on this conclusion, it is possible to disregard a non-contact wave of deformation.

We obtained analytical dependences of contact area under ultrasonic smoothness with a preceding gap on treatment parameters, namely, the treatment speed, the feed rate, the radius of an operation surface of a tool. The results of mathematical modeling and experimental data are quite close. We defined the region of optimal feed, which makes it possible to obtain surfaces with minimal roughness or microrelief.

Author Biographies

Valery Тurych, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

PhD, Associate Professor

Department of machinery and equipment for agricultural production

Volodymyr Rutkevych, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

PhD

Department of machinery and equipment for agricultural production

Natalia Goncharuk, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

PhD

Department of feeding s.-g. animals and aquatic bioresources

Galina Ogorodnichuk, Vinnytsia National Agrarian University Soniachna str., 3, Vinnytsia, Ukraine, 21008

PhD, Associate Professor

Department of livestock production technology

References

  1. Kanarchuk, V. Ye., Posviatenko, E. K., Lopata, L. A. (2000). Inzheneriya poverkhni detalei transportnykh zasobiv: suchasnyi stan i perspektyvy. Visnyk NTU, 4, 6–24.
  2. Posviatenko, E. K., Posviatenko, E. K., Turych, V. V., Shevchenko, V. I. (2003). Modyfikuvannia poverkhni detalei mashyn ultrazvukovym metodom. Visnyk NTU, 8, 28–33.
  3. Astashev, V. K. (1983). O vliyanii vysokochastotnyh vibraciy na processy plasticheskogo deformirovaniya. Mashinovedenie, 2, 3–12.
  4. Rimkeviciene, J., Ostasevicius, V., Jurenas, V., Gaidys, R. (2009). Experiments and simulations of ultrasonically assisted turning tool. Mechanika, 1, 42–46.
  5. Moriwaki, T. (2010). Development of 2DOF Ultrasonic Vibration Cutting Device for Ultraprecision Elliptical Vibration Cutting. Key Engineering Materials, 447-448, 164–168. doi: 10.4028/www.scientific.net/kem.447-448.164
  6. Demkin, N. B., Ryzhov, E. V. (1981). Kachestvo poverhnosti i kontakt detaley mashin. Moscow: Mashinostroenie, 244.
  7. Odincov, L. G. (1987). Uprochnenie i otdelka detaley poverhnostnym plasticheskim deformirovaniem. Moscow: Mashinostroenie, 328.
  8. Adler, Yu. P., Markova, E. V., Granovskiy, Yu. V. (1976). Planirovanie eksperimenta pri poiske optimal'nyh usloviy. Moscow: Nauka, 278.
  9. Kalashnikov, V. V., Valogin, M. F., Nerubai, M. C., Shtrykov, B. L., Khan, F. R. (2002). Ultrasonic physico-chemical methods of processing and assembly. New Delhi, 161.
  10. Turych, V. V., Rutkevych, V. S. (2016). Kontaktna vzaiemodiya instrumenta z detalliu v protsesi deformuiuchoho protiahuvannia z ultrazvukom. Promyslova hidravlika i pnevmatyka, 4 (54), 71–76.
  11. Turych, V., Weselowskaya, N., Rutkevych, V., Shargorodskiy, S. (2017). Investigation of the process of thread extrusion using the ultrasound. Eastern-European Journal of Enterprise Technologies, 6 (1 (90)), 60–68. doi: 10.15587/1729-4061.2017.114564
  12. Kumar, J. (2013). Ultrasonic machining – a comprehensive review. Machining Science and Technology, 17 (3), 325–379. doi: 10.1080/10910344.2013.806093
  13. Bernhard, K. (2002). Ultraschallbehandlung zur Herstellung von Teilen aus spröden Materialien. Ein harter Job. Maschinenmarkt, 108 (12), 24–25.
  14. Japitana, F. H., Morishige, K., Yasuda, S., Takeuchi, Y. (2003). Manufacture of Overhanging Sharp Corner by Means of 6-Axis Control Machining with the Application of Ultrasonic Vibrations. JSME International Journal Series C, 46 (1), 306–313. doi: 10.1299/jsmec.46.306
  15. Khan. F. R. (2001). Finite element analysis (FAE) model of ultrasonic assembly process in Mechanical engineering. International journal of mechanical engineers, 58–66.
  16. Turych, V. V., Rutkevych, V. S. (2012). Pat. No. 70985 UA. Sposib ultrazvukovoi zmitsniuiuchoi obrobky. MPK B24B 39/00. No. u20120046; declareted: 16.01.2012; published: 25.06.2012, Bul. No. 12.
  17. Turych, V. V., Rutkevych, V. S. (2015). Pat. No. 101967 UA. Prystriy dlia vymiriuvannia parametriv ultrazvukovykh kolyvan. MPK G01H 1/08. No. u201503354; declareted: 10.04.2015; published: 12.10.2015, Bul. No. 19.
  18. Urbikain, G., Perez, J. M., López de Lacalle, L. N., Andueza, A. (2016). Combination of friction drilling and form tapping processes on dissimilar materials for making nutless joints. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 232 (6), 1007–1020. doi: 10.1177/0954405416661002
  19. Klubovich, V. V., Stepanenko, A. V. (1981). Ul'trazvukovaya obrabotka materialov. Minsk: Nauka i tekhnika, 295.
  20. Kumabe, D. (1985). Vibracionnoe rezanie. Moscow: Mashinostroenie, 424.

Downloads

Published

2018-05-14

How to Cite

Тurych V., Rutkevych, V., Goncharuk, N., & Ogorodnichuk, G. (2018). Investigation of the process of smoothing with ultrasound. Eastern-European Journal of Enterprise Technologies, 3(1 (93), 22–33. https://doi.org/10.15587/1729-4061.2018.131047

Issue

Vol. 3 No. 1 (93) (2018): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2018 Valery Тurych, Volodymyr Rutkevych, Natalia Goncharuk, Galina Ogorodnichuk

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.