A study to determine the onset of catastrophic wear of a processing tool by statistical parameters of acoustic emission
DOI:
https://doi.org/10.15587/1729-4061.2019.184959Keywords:
acoustic emission, composite material, statistical amplitude parameters, mechanical processing of materials, wear of a processing toolAbstract
In the present study, experimental research was carried out to determine the effect of the processing tool wear on the mutual change in the average statistical amplitude parameters of acoustic emission signals. Acoustic emission signals were recorded when turning silumin. The research was aimed at finding parameters to determine the occurrence of critical wear of the processing tool. It is shown that the recorded signals are continuous. The statistical amplitude parameters of the acoustic emission signals were processed under normal and catastrophic wear of the processing tool. It has been determined that the development of normal and catastrophic wear of the tool leads to a decrease in the values of the statistical amplitude parameters of the recorded signals. However, no peculiarities were found in their change to determine the developing type of wear. Meanwhile, at different time intervals, there was an anticipating increase or decrease in one of the statistical amplitude parameters of the acoustic emission signals.
The processed parameter was a coefficient characterising a mutual change in the statistical amplitude values of the recorded signals. It has been determined that absence of the tool wear is characterised by stable values of the calculated coefficient in time. The occurrence and development of catastrophic wear leads to an outburst of the value of the calculated coefficient with its subsequent accelerated decrease to the destruction of the tool. The emergence and development of normal wear leads to an increase in the value of the calculated coefficient with a subsequent transition to a sawtooth change and a gradual decrease of its size. The obtained regularities can be used when devising methods for controlling and monitoring the condition of the tool during the mechanical processing of materials, including monitoring the state of the processing tool in robotic industriesReferences
- Bhaskaran, J., Murugan, M., Balashanmugam, N., Chellamalai, M. (2012). Monitoring of hard turning using acoustic emission signal. Journal of Mechanical Science and Technology, 26 (2), 609–615. doi: https://doi.org/10.1007/s12206-011-1036-1
- Kulandaivelu, P., Kumar, P. S. (2012). Investigate the Crater Wear Monitoring of Single Point Cutting Tool Using Adaptive Neuro Fuzzy Inference System. Journal of Applied Science and Engineering, 15 (3), 265–274.
- Fadare, D. A., Sales, W. F., Bonney, J., Ezugwu, E. O. (2012). Influence of cutting parameters and tool wear on acoustic emission signal in high-speed turning of Ti-6Al-4V Alloy. Journal of Emerging Trends in Engineering and Applied Sciences, 3 (3), 547–555.
- Chang, L. F., Lu, M. C., Chen, K. H., Wu, C. C. (2014). Development of Condition Monitoring System for Micro Milling of PZT Deposited Si Wafer. 9th International workshop on microfactories - IWMF2014, 139–145.
- Qin, F., Hu, J., Chou, Y. K., Thompson, R. G. (2009). Delamination wear of nano-diamond coated cutting tools in composite machining. Wear, 267 (5-8), 991–995. doi: https://doi.org/10.1016/j.wear.2008.12.065
- Mascaro, B., Gibiat, V., Bernadou, M., Esquerre, Y. (2005). Acoustic emission of the drilling of Carbon/Epoxy composites. Proc. of the Forum Acusticum. Budapest, 2823–2827.
- Olufayo, O. A., Abou-El-Hossein, K. (2013). Acoustic Emission Monitoring in Ultra-High Precision Machining of Rapidly Solidified Aluminium. Proceedings International Conference on Competitive Manufacturing. Stellenbosch, 307–312.
- Prakash, M., Kanthababu, M., Gowri, S., Balasubramaniam, R., Jegaraj, J. R. (2014). Tool Condition Monitoring using Multiple Sensors Approach in theMicroendmilling of Aluminium Alloy (AA1100). 5th International & 26th All India Manufacturing Technology, Design and Research Conference - AIMTDR 2014. IIT Guwahati, Assam, 394-1–394-6.
- Mukhopadhyay, C. K., Jayakumar, T., Raj, B., Venugopal, S. (2012). Statistical analysis of acoustic emission signals generated during turning of a metal matrix composite. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 34 (2), 145–154. doi: https://doi.org/10.1590/s1678-58782012000200006
- Bhuiyan, M. S. H., Choudhury, I. A., Dahari, M., Nukman, Y., Dawal, S. Z. (2016). Application of acoustic emission sensor to investigate the frequency of tool wear and plastic deformation in tool condition monitoring. Measurement, 92, 208–217. doi: https://doi.org/10.1016/j.measurement.2016.06.006
- Papacharalampopoulos, A., Stavropoulos, P., Doukas, C., Foteinopoulos, P., Chryssolouris, G. (2013). Acoustic Emission Signal Through Turning Tools: A Computational Study. Procedia CIRP, 8, 426–431. doi: https://doi.org/10.1016/j.procir.2013.06.128
- Hase, A., Wada, M., Koga, T., Mishina, H. (2013). The relationship between acoustic emission signals and cutting phenomena in turning process. The International Journal of Advanced Manufacturing Technology, 70 (5-8), 947–955. doi: https://doi.org/10.1007/s00170-013-5335-9
- Albers, A., Stürmlinger, T., Wantzen, K., Bartosz, Gladysz, Münke, F. (2017). Prediction of the Product Quality of Turned Parts by Real-time Acoustic Emission Indicators. Procedia CIRP, 63, 348–353. doi: https://doi.org/10.1016/j.procir.2017.03.173
- Abdi, H., Williams, L. J. (2010). Principal component analysis. Wiley Interdisciplinary Reviews: Computational Statistics, 2 (4), 433–459. doi: https://doi.org/10.1002/wics.101
- Teti, R. (2015). Advanced IT Methods of Signal Processing and Decision Making for Zero Defect Manufacturing in Machining. Procedia CIRP, 28, 3–15. doi: https://doi.org/10.1016/j.procir.2015.04.003
- Segreto, T., Simeone, A., Teti, R. (2013). Multiple Sensor Monitoring in Nickel Alloy Turning for Tool Wear Assessment via Sensor Fusion. Procedia CIRP, 12, 85–90. doi: https://doi.org/10.1016/j.procir.2013.09.016
- Kong, D., Chen, Y., Li, N., Tan, S. (2016). Tool wear monitoring based on kernel principal component analysis and v-support vector regression. The International Journal of Advanced Manufacturing Technology, 89 (1-4), 175–190. doi: https://doi.org/10.1007/s00170-016-9070-x
- Caggiano, A. (2018). Tool Wear Prediction in Ti-6Al-4V Machining through Multiple Sensor Monitoring and PCA Features Pattern Recognition. Sensors, 18 (3), 823. doi: https://doi.org/10.3390/s18030823
- Filonenko, S. F. (2016). Acoustic energy at controlled cutting depth of composite material. Electronics and Control Systems, 3 (49), 93–99. doi: https://doi.org/10.18372/1990-5548.49.11244
- Filonenko, S. (2017). Acoustic emission at treating tool wear with a not controlled cutting depth. Proceedings of the National Aviation University, 70 (1), 90–97. doi: https://doi.org/10.18372/2306-1472.70.11426
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Sergii Filonenko, Anzhelika Stakhova
![Creative Commons License](http://i.creativecommons.org/l/by/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.