Effect of the tool geometry on the force mode of the combined radial-direct extrusion with compression

Authors

DOI:

https://doi.org/10.15587/1729-4061.2020.198433

Keywords:

combined extrusion, upper estimate, kinematic module, energy method, deformation process, components with a flange

Abstract

A possibility has been investigated to use an energy method to calculate the energy-force parameters for the cold extrusion processes involving components of complex configuration. A mathematical model has been proposed for the process of combined sequential radial-direct extrusion with compression with the presence of triangular kinematic modules. The use of the triangular kinematic modules with curvilinear and straight-line boundaries has made it possible to describe the sites of intense deformation, which correspond to the steady stage of the deformation process. It has been proposed to apply an upper estimate of the power of forces that deform a kinematic module of the triangular shape of the transition zone from the radial flow of metal to direct extrusion. This has made it possible to derive the magnitude of the reduced deformation pressure in the analytical form as a function of the geometric and technological parameters of the extrusion process. The margin of error, compared to numerical calculations without the use of the upper estimate, does not exceed 0.2‒1 %. The role of an optimization parameter belongs to aÎ(0,1), which is responsible for the shape of the curvilinear boundary of the inner triangular kinematic module. We have derived an analytical expression for the optimal value of the α parameter and analyzed a change in the magnitude of the reduced deformation pressure at different ratios of the process geometric parameters. It has been established that the optimal values of the angle of inclination of the forming mandrel β lie between 20° and 30° for different ratios of the deformation process.

It has been justified that the use of combined sequential extrusion in the manufacture of hollow components with a flange, when compared to the application of simple deformation schemes, improves the process technological possibilities. The lack of study of the schemes of the combined radial-direct extrusion process with the compression of components of the type of sleeve, as well as the lack of recommendations for calculating the energy force parameters of the process, have been confirmed. The calculation scheme of a given process, developed on the basis of an energy method, makes it possible to predict the force mode for the steady stage under different technological parameters of the deformation process. The data acquired on the estimation of the optimal parameters for tool configuration would help devise appropriate design and technology recommendations

Author Biographies

Leila Aliieva, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

Doctor of Technical Sciences, Associate Professor

Department of Metal Forming

Natalia Hrudkina, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

PhD

Department of Metal Forming

Igramotdin Aliiev, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

Doctor of Technical Sciences, Professor, Head of Department

Department of Metal Forming

Iaroslav Zhbankov, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

Doctor of Technical Sciences, Associate Professor

Department of Metal Forming

Oleg Markov, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

Doctor of Technical Sciences, Professor, Head of Department

Department of Computerized Design and Modeling of Processes and Machines

References

  1. Bhaduri, A. (2018). Extrusion. Springer Series in Materials Science, 599–646. doi: https://doi.org/10.1007/978-981-10-7209-3_13
  2. Aliiev, I. S. (1988). Radial extrusion processes. Soviet Forging and Sheet Metal Stamping Technology, 6, 1–4.
  3. Saffar, S., Malaki, M., Mollaei-Dariani, B. (2014). On the effects of eccentricity in precision forging process. UPB Scientific Bulletin, Series D: Mechanical Engineering, 76 (1), 123–138.
  4. Aliiev, I. S., Lobanov, A. I., Borisov, R. S., Savchinskij, I. G. (2004). Investigation of die blocks with split matrixes for the processes of cross extrusion. Kuznechno-Shtampovochnoe Proizvodstvo (Obrabotka Metallov Davleniem), 8, 21–26.
  5. Aliieva, L. I. (2016). Protsessy kombinirovannogo plasticheskogo deformirovaniya i vydavlivaniya. Obrabotka materialov davleniem, 1, 100–108.
  6. Kalyuzhnyi, V. L., Alieva, L. I., Kartamyshev, D. A., Savchinskii, I. G. (2017). Simulation of Cold Extrusion of Hollow Parts. Metallurgist, 61 (5-6), 359–365. doi: https://doi.org/10.1007/s11015-017-0501-1
  7. Jafarzadeh, H., Zadshakoyan, M., Abdi Sobbouhi, E. (2010). Numerical Studies of Some Important Design Factors in Radial-Forward Extrusion Process. Materials and Manufacturing Processes, 25 (8), 857–863. doi: https://doi.org/10.1080/10426910903536741
  8. Xue, Y., Bai, B., Chen, S., Li, H., Zhang, Z., Yang, B. (2017). Study on processing and structure property of Al-Cu-Mg-Zn alloy cup-shaped part produced by radial-backward extrusion. The International Journal of Advanced Manufacturing Technology, 95 (1-4), 687–696. doi: https://doi.org/10.1007/s00170-017-1073-8
  9. Shatermashhadi, V., Manafi, B., Abrinia, K., Faraji, G., Sanei, M. (2014). Development of a novel method for the backward extrusion. Materials & Design (1980-2015), 62, 361–366. doi: https://doi.org/10.1016/j.matdes.2014.05.022
  10. Aliieva, L., Zhbankov, Y. (2015). Radial-direct extrusion with a movable mandrel. Metallurgical and Mining Industry, 11, 175–183.
  11. Farhoumand, A., Khoddam, S., Hodgson, P. D. (2012). A study of plastic deformation during axisymmetric forward spiral extrusion and its subsequent mechanical property changes. Modelling and Simulation in Materials Science and Engineering, 20 (8), 085005. doi: https://doi.org/10.1088/0965-0393/20/8/085005
  12. Murata, M., Kuboki, T., Kobayashi, M., Yamazaki, H. (2012). Influence of Billet Material of Extruded Circular Tube with Spiral Projections on Inside Wall. Influence of billet material of extruded circular tube with spiral projections on inside wall, Metal forming. Krakow, 463–466.
  13. Noh, J., Hwang, B. B., Lee, H. Y. (2015). Influence of punch face angle and reduction on flow mode in backward and combined radial backward extrusion process. Metals and Materials International, 21 (6), 1091–1100. doi: https://doi.org/10.1007/s12540-015-5276-y
  14. Jamali, S. S., Faraji, G., Abrinia, K. (2016). Hydrostatic radial forward tube extrusion as a new plastic deformation method for producing seamless tubes. The International Journal of Advanced Manufacturing Technology, 88 (1-4), 291–301. doi: https://doi.org/10.1007/s00170-016-8754-6
  15. Ogorodnikov, V. А., Dereven’ko, I. А., Sivak, R. I. (2018). On the Influence of Curvature of the Trajectories of Deformation of a Volume of the Material by Pressing on Its Plasticity Under the Conditions of Complex Loading. Materials Science, 54 (3), 326–332. doi: https://doi.org/10.1007/s11003-018-0188-x
  16. Noh, J., Hwang, B.-B. (2015). Numerical analysis of tool geometry effect on the wear characteristics in a radial forward extrusion. Journal of Mechanical Science and Technology, 29 (8), 3447–3457. doi: https://doi.org/10.1007/s12206-015-0743-4
  17. Farhoumand, A., Ebrahimi, R. (2016). Experimental investigation and numerical simulation of plastic flow behavior during forward-backward-radial extrusion process. Progress in Natural Science: Materials International, 26 (6), 650–656. doi: https://doi.org/10.1016/j.pnsc.2016.12.005
  18. Aliiev, I., Aliieva, L., Grudkina, N., Zhbankov, I. (2011). Prediction of the Variation of the Form in the Processes of Extrusion. Metallurgical and Mining Industry, 3 (7), 17–22.
  19. Motallebi Savarabadi, M., Faraji, G., Zalnezhad, E. (2019). Hydrostatic tube cyclic expansion extrusion (HTCEE) as a new severe plastic deformation method for producing long nanostructured tubes. Journal of Alloys and Compounds, 785, 163–168. doi: https://doi.org/10.1016/j.jallcom.2019.01.149
  20. Ebrahimi, R., Reihanian, M., Moshksar, M. M. (2008). An analytical approach for radial-forward extrusion process. Materials and Design, 29, 1694–1700.
  21. Noh, J. H., Hwang, B. B. (2017). Work efficiency in a double cup extrusion process. International Journal of Precision Engineering and Manufacturing, 18 (3), 407–414. doi: https://doi.org/10.1007/s12541-017-0049-9
  22. Alyushin, Yu. A. (2012). Mehanika tverdogo tela v peremennyh Lagranzha. Moscow: Mashinostroenie, 192.
  23. Chudakov, P. D. (1992). Verhnyaya otsenka moshchnosti plasticheskoy deformatsii s ispol'zovaniem minimiziruyushchey funktsii. Izvestiya vuzov. Mashinostroenie, 9, 13–15.
  24. Unksov, E. P., Dzhonson, U., Kolmogorov, V. L., Ogorodnikov, V. A. et. al.; Unksov, E. P., Ovchinnikov, A. G. (Eds.) (1992). Teoriya kovki i shtampovki. Moscow: Mashinostroenie, 720.
  25. Hrudkina, N., Aliieva, L., Abhari, P., Kuznetsov, M., Shevtsov, S. (2019). Derivation of engineering formulas in order to calculate energy-power parameters and a shape change in a semi-finished product in the process of combined extrusion. Eastern-European Journal of Enterprise Technologies, 2 (7 (98)), 49–57. doi: https://doi.org/10.15587/1729-4061.2019.160585
  26. Hrudkina, N., Aliieva, L., Abhari, P., Markov, O., Sukhovirska, L. (2019). Investigating the process of shrinkage depression formation at the combined radial-backward extrusion of parts with a flange. Eastern-European Journal of Enterprise Technologies, 5 (1 (101)), 49–57. doi: https://doi.org/10.15587/1729-4061.2019.179232
  27. Vlasenko, K., Hrudkina, N., Reutova, I., Chumak, O. (2018). Development of calculation schemes for the combined extrusion to predict the shape formation of axisymmetric parts with a flange. Eastern-European Journal of Enterprise Technologies, 3 (1 (93)), 51–59. doi: https://doi.org/10.15587/1729-4061.2018.131766

Downloads

Published

2020-04-30

How to Cite

Aliieva, L., Hrudkina, N., Aliiev, I., Zhbankov, I., & Markov, O. (2020). Effect of the tool geometry on the force mode of the combined radial-direct extrusion with compression. Eastern-European Journal of Enterprise Technologies, 2(1 (104), 15–22. https://doi.org/10.15587/1729-4061.2020.198433

Issue

Vol. 2 No. 1 (104) (2020): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2020 Leila Aliieva, Natalia Hrudkina, Igramotdin Aliiev, Iaroslav Zhbankov, Oleg Markov

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.