Determining mechanical properties at the shear of the material of "T" type pressure fire hose based on torsion tests
DOI:
https://doi.org/10.15587/1729-4061.2020.212269Keywords:
pressure fire hose, working pressure, elasticity module, hysteresis, dissipative properties, torsionAbstract
This paper reports the results of experimental studies into determining mechanical properties (elastic and dissipative) at the shear of the material of a pressure fire hose of the "T" type with the internal diameter of 77 mm using torsion tests. During the studies, a series of field experiments have been conducted on the torsion of the pressure fire hose samples with internal hydraulic pressure (P) in a hose of 0.2 МPа (Р1), 0.4 МPа (Р2), and 0.6 МPа (Р3) under conditions of static loading-unloading cycles. The tests consisted of 6 cycles – for each of the (P) loading-unloading cycles, which were carried out at a two-minute interval, the rigidity and elasticity modules at the shear of the material of a hose were determined by means of torsion tests. It was established that the numerical results of mechanical properties depend on the hose load "history", that is, the elasticity modules increased in the first two, three load cycles, and they stabilized only afterward at the level of 3.04 MPa for Р1, 4.35 МPа for Р2, 4.39 МPа for Р3. The above, together with a significant decrease in residual deformations, strengthens the elastic properties of the fire hose material.
The results of the research have been approximated by the corresponding trend lines. The equation of dependence of the current torque on deformation was determined. The curves of the deformation of samples, which, under the conditions of cyclic loading-unloading, formed hysteresis loops, were established. The resulting hysteresis loops during the study in the first two modes undergo quantitative and qualitative changes, namely, the slope and its area decrease. The similarity of experimental studies at different internal pressures (P) was established.
A change in the properties of the material of a fire hose at the consecutive loading-unloading deformation cycles is reverse, the gaps between the deformation cycles lead to a partial restoration of the mechanical characteristics, approximating them to the original valuesReferences
- Kovalenko, R., Kalynovskyi, A., Nazarenko, S., Kryvoshei, B., Grinchenko, E., Demydov, Z. et. al. (2019). Development of a method of completing emergency rescue units with emergency vehicles. Eastern-European Journal of Enterprise Technologies, 4 (3 (100)), 54–62. doi: https://doi.org/10.15587/1729-4061.2019.175110
- Dubinin, D., Korytchenko, K., Lisnyak, A., Hrytsyna, I., Trigub, V. (2017). Numerical simulation of the creation of a fire fighting barrier using an explosion of a combustible charge. Eastern-European Journal of Enterprise Technologies, 6 (10 (90)), 11–16. doi: https://doi.org/10.15587/1729-4061.2017.114504
- Tiutiunyk, V. V., Ivanets, H. V., Tolkunov, I. A., Stetsyuk, E. I. (2018). System approach for readiness assessment units of civil defense to actions at emergency situations. Scientific Bulletin of National Mining University, 1, 99–105. doi: https://doi.org/10.29202/nvngu/2018-1/7
- Larin, O., Chernobay, G., Kohanenko, V., Nazarenko, S. (2015). A study of longitudinal stiffness of t-type fire hoses with 77mm diameter with structural elements fire hose. Visnyk Natsionalnoho tekhnichnoho universytetu "Kharkivskyi politekhnichnyi instytut". Seriya: Novi rishennia v suchasnykh tekhnolohiyakh, 39, 41–46.
- Fedorko, G., Molnar, V., Dovica, M., Toth, T., Fabianova, J. (2015). Failure analysis of irreversible changes in the construction of the damaged rubber hoses. Engineering Failure Analysis, 58, 31–43. doi: https://doi.org/10.1016/j.engfailanal.2015.08.042
- Cho, J.-R., Yoon, Y.-H. (2016). Large deformation analysis of anisotropic rubber hose along cyclic path by homogenization and path interpolation methods. Journal of Mechanical Science and Technology, 30 (2), 789–795. doi: https://doi.org/10.1007/s12206-016-0134-5
- Cho, J. R., Yoon, Y. H., Seo, C. W., Kim, Y. G. (2015). Fatigue life assessment of fabric braided composite rubber hose in complicated large deformation cyclic motion. Finite Elements in Analysis and Design, 100, 65–76. doi: https://doi.org/10.1016/j.finel.2015.03.002
- Traxl, R., Mungenast, D., Schennach, O., Lackner, R. (2019). Mechanical performance of textile-reinforced hoses assessed by a truss-based unit cell model. International Journal of Engineering Science, 141, 47–66. doi: https://doi.org/10.1016/j.ijengsci.2019.05.006
- Motorin, L. V., Stepanov, O. S., Bratolyubova, E. V. (2011). The simplified mathematical model for strength calculation of pressure fire hoses under hydraulic influence. Tehnologiya tekstil'noy promyshlennosti, 1, 126–133.
- Kobeyeva, N. M., Togatayev, T. U., Yeldiyar, G. K., Kuralbayeva, A. N., Zholayeva, N. Kh., Sadyrbayeva, I. R. (2016). Geometrical densities according to warp and weft yarns of fabric reinforcing framework of fire hoses. Science and world, 1 (5 (33)), 90–91.
- Larin, O. O. (2015). Probabilistic Model of Fatigue Damage Accumulation in Rubberlike Materials. Strength of Materials, 47 (6), 849–858. doi: https://doi.org/10.1007/s11223-015-9722-3
- Larin, A. A., Vyazovichenko, Y. A., Barkanov, E., Itskov, M. (2018). Experimental Investigation of Viscoelastic Characteristics of Rubber-Cord Composites Considering the Process of Their Self-Heating. Strength of Materials, 50 (6), 841–851. doi: https://doi.org/10.1007/s11223-019-00030-7
- Larin, O., Morozov, O., Nazarenko, S., Chernobay, G., Kalynovskyi, A., Kovalenko, R. et. al. (2019). Determining mechanical properties of a pressure fire hose the type of «T». Eastern-European Journal of Enterprise Technologies, 6 (7 (102)), 63–70. doi: https://doi.org/10.15587/1729-4061.2019.184645
- Haseeb, A. S. M. A., Jun, T. S., Fazal, M. A., Masjuki, H. H. (2011). Degradation of physical properties of different elastomers upon exposure to palm biodiesel. Energy, 36 (3), 1814–1819. doi: https://doi.org/10.1016/j.energy.2010.12.023
- Lee, G.-C., Kim, H.-E., Park, J.-W., Jin, H.-L., Lee, Y.-S., Kim, J.-H. (2011). An experimental study and finite element analysis for finding leakage path in high pressure hose assembly. International Journal of Precision Engineering and Manufacturing, 12 (3), 537–542. doi: https://doi.org/10.1007/s12541-011-0067-y
- Pavloušková, Z., Klakurková, L., Man, O., Čelko, L., Švejcar, J. (2015). Assessment of the cause of cracking of hydraulic hose clamps. Engineering Failure Analysis, 56, 14–19. doi: https://doi.org/10.1016/j.engfailanal.2015.05.014
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2020 Sergii Nazarenko, Roman Kovalenko, Vitalii Asotskyi, Gennadiy Chernobay, Andrii Kalynovskyi, Ivan Tsebriuk, Oleksandr Shapovalov, Igor Shasha, Volodymyr Demianyshyn
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.
