Adaptive system of controlling temperature mode of polymer materials extrusion

Authors

DOI:

https://doi.org/10.15587/1729-4061.2014.24625

Keywords:

extruder, control system, adaptation, controller, identification model

Abstract

An adaptive system of controlling the temperature mode of an extruder under normal operation conditions is presented. The analysis concerning the importance of maintaining the given temperature of the extruder when manufacturing polymer materials was carried out. The necessity in applying the principle of adaptation while conducting the process was substantiated. As a controlling object, a single-screw three-zone extruder was used. As a model, the autoregressive-moving average model was proposed. The results of studying the adaptive control system with different methods of identifying the model parameters, basing on the recursive methods of least squares and their modifications, were given. The synthesis and studies of various structures of the adaptive controller were carried out. On the pretext of the conducted studies, the most effective structure of the adaptive control system, which supports the device at the specified temperature level, was proposed.

Author Biography

Олексій Жученко, National Technical University of Ukraine “Kyiv Polytechnic Institute” Peremogy ave, 37, Bldg. 19, Kyiv, 03056

Docent

Department of Chemical Automation manufactures

References

  1. Ким, В. С. Теория и практика экструзии полимеров [Текст] / В. С. Ким. – КОЛОСС, 2005. – 568 с.
  2. Раувендаль, К. Экструзия полимеров [Текст] / К. Раувендаль. – СПб.: Профессия, 2006. – 768 с.
  3. Tadmor, Z. Principles of Polymer Processing [Text] / Z. Tadmor, C. G. Gogos. – Wiley Interscience, 2006. – 961 p.
  4. Wang, Y.- T. Modelling and Control for a Thermal Вarrel in Plastic Molding Process [Text] / Y.-T. Wang, S.-L. Wu // Tamkang Journal of Science and Engineering. – 2006. – Vol. 9, № 2. – P. 129–140.
  5. Dubay, R. Temperature control of injection molding. Part 2: Controller design, simulation, and implementation [Text] / R. Dubay, C. Diduch, W.G. Li // Polym.Eng. Sci. – 2004. – № 44, no. 12. – P. 2318–2326.
  6. Dassau, E. Modeling and temperature control of rapid thermal processing [Text] / E. Dassau, B. Grosman, D. R. Lewin // Comput. Chem. Eng. – 2006. – № 30, no. 4. – P. 686–697.
  7. Раувендаль, К. Выявление и устранение проблем в экструзии [Текст] / К. Раувендаль, М. П. Норега, Х. Харрис. – СПб.: Профессия, 2008. – 328 с.
  8. Tsai, С.-С. Fuzzy supervisory predictive PID control of a plastics extruder barrel [Text] / Ching-Chih Tsai, Chi-Huang Lu // Journal of the Chinese Institute of Engineers. – 1998. – № 21. – P. 619–624.
  9. Ravi, S. Design of Intelligent Self-Tuning GA ANFIS Temperature Controller for Plastic Extrusion System [Text] / S. Ravi, М. Sudha, Р. Balakrishnan // Hindawi Publishing Corporation Modelling and Simulation in Engineering Volume. – 2011. –№ 12.– P. 611–624.
  10. Abeykoon, С. Extruder Melt Temperature Control With Fuzzy Logic [Text] / C. Abeykoon, K. Li, M. McAfee, P. J. Martin, G. W. Irwin // Preprints of the 18th IFAC World Congress Milano (Italy), 2011. – P. 8577–8582.
  11. Yusuf, I. Temperature Control for Plastic Extruder Used Fuzzy Genetic Algorithms [Text] / I. Yusuf, N. Iksan, N.A. Suryana Herman // Proceedings of the International MultiConference of Engineers and Computer scientists. – 2010. – №2.
  12. Хобин, В. А. Управление процессом экструдирования растительного сырья в условиях ограниченности ресурсов и неопределенностей [Текст] : cб. докл. II Всеукр. науч.-практ. конф./ В. А. Хобин, В. Б. Егоров // Информационные технологии и автоматизация – 2009. – Одесса: ОНАПТ, 2009. – С. 30–31.
  13. Эйкхофф, П. Основы идентификации систем управления [Текст] : учебник / П. Эйкхофф. – М.: Мир, 1975. – 683 с.
  14. Антонов, В. Н. Адаптивное управление в технических системах [Текст] / В. Н. Антонов, В. А. Терехов, И. Ю. Тюкин. – СПб.: изд-во С.-Петербургского университета, 2001. – 244 с.
  15. Методы робастного, нейро – нечеткого и адаптивного управления [Текст] / Под ред. Н. Д. Егупова. – М.: Изд-во МТТУ им. Н. Э.Баумана, 2002. – 744 с.
  16. Жученко, О. А. Адаптивне керування процесом екструзії пластичних мас [Текст] / О. А. Жученко, Л. Д. Ярощук // Контроль і управління в складних системах (КУСС-2008): доповіді IX Міжнародної конференції, 21-24 жовтня 2008р, Секц.4, Вінниця, ВПІ, 2008. – 15 с.
  17. Острем, К. Системы управления с ЭВМ [Текст] : учебник / К. Острем, Б. Виттенмарк. – М.: Мир, 1987. – 480 с.
  18. Lu, Q. Model and strategies for computer control of a twin-extruder [Text] / Q. Lu, S. J. Mulvaney, F. Hsieh, H. E. Huff. – Food Control, 4,1993. – P. 25–33.
  19. Александровский, Н. М. Адаптивные системы автоматического управления сложными технологическими процессами [Текст] : учебник / Н. М. Александровский, С. В. Егоров, Р. Е. Кузин. – М.: Энергия, 1979. – 272 с.
  20. Soderstrom, T. A theoretical analysis of recursive identification metods [Text] / T. Soderstrom, L. Ljung, I. Gustavsson // Automatica. – 1978. – Vol.14, № 3. – P. 231–244.
  21. Жученко, О. А. Дослідження алгоритмів ідентифікації параметрів моделі в адаптивній системі керування екструдером [Текст] / О. А. Жученко, П. І. Бідюк // Адаптивні системи автоматичного управління // Міжвідомчій науково-технічний збірник. – 2010. – Вип. 16 (36). – С. 147–154.
  22. Kim, V. S. (2005). Theory and practice of polymer extrusion. Koloss, 568.
  23. Rauvendal, К. (2006). Polymeric extrusion. St. Petersburg.: Professiya, 768.
  24. Tadmor, Z., Gogos, C. G. (2006). Principles of Polymer Processing. Wiley Interscience, 961.
  25. Wang, Y.-T., Wu, S.-L. (2006). Modelling and Control for a Thermal Вarrel in Plastic Molding Process. Tamkang Journal of Science and Engineering, Vol. 9, № 2, 129–140.
  26. Dubay, R., Diduch, C., Li, W. G. (2004). Temperature control of injection molding. Part 2: Controller design, simulation, and implementation. Polym.Eng. Sci., №44, no. 12, 2318–2326.
  27. Dassau, E., Grosman, B., Lewin, D. R. (2006). Modeling and temperature control of rapid thermal processing. Comput. Chem. Eng., № 30, № 4, 686–697.
  28. Rauvendal, К., Norega, M. P., Harys, H. (2008). Identification and elimination of problems in extrusion. St. Petersburg.: Professiya, 328.
  29. Tsai, С.-С., Tsai, C.-C., Lu, C-H. (1998). Fuzzy supervisory predictive PID control of a plastics extruder barrel. Journal of the Chinese Institute of Engineers, Vol. 21, Issue 5, 619-624.
  30. Ravi, S., Sudha, М., Balakrishnan, Р. (2011). Design of Intelligent Self-Tuning GA ANFIS Temperature Controller for Plastic Extrusion. Hindawi Publishing Corporation Modelling and Simulation in Engineering, Vol. 12, 611-624.
  31. Abeykoon, С., Li, K., McAfee, M., Martin, P, Irwin, G. (2011). Extruder Melt Temperature Control With Fuzzy Logic. Preprints of the 18th IFAC World Congress Milano (Italy), 8577–8582.
  32. Yusuf, I., Iksan, N., Suryana Herman, N. A. (2010). Temperature Control for Plastic Extruder Used Fuzzy Genetic Algorithms. Proceedings of the International MultiConference of Engineers and Computer scientists, Vol. 2.
  33. Hobin, V. А., Egorov, V. B. (2009). Managing the process of extrusion plant materials under conditions of limited resources and uncertainty. «Information technology and automation – 2009», Odessa, 30–31.
  34. Eykhoff, P. (1975) Basics identification management systems. Moscow, 683.
  35. Antonov, V. N., Terehov, V. A., Tukin, I. Y. (2001). Adaptive control in engineering systems. St. Petersburg, 244.
  36. Egupov, N. D. (2002). Robust methods, neuro - fuzzy and adaptive control. Moscow, 744.
  37. Zhuchenko, О. А., Yaroschuk, L. D. (2008). Adaptive process control extrusion plastics. Monitoring and control of complex systems (MCCS-2008): Vonnitsa, 15.
  38. Ostrem, К, Vittenmark, B. (1987). Control system with computer. Moscow, 480.
  39. Lu, Q., Mulvaney, S. J., Hsieh, F., Huff, H. E. (1993). Model and strategies for computer control of a twin-extruder. Food Control, 4, 25-33.
  40. Aleksandrovskiy, N. М., Egorov, S. V., Kuzin, R. E. (1979). Adaptive systems of automatic control of complex technological processes. Moscow, 272.
  41. Soderstrom, T., Ljung, L., Gustavsson, I. (1978). A theoretical analysis of recursive identification metods. Automatica, Vol.14, №3, 231-244.
  42. Zhuchenko, О. А., Bidyuk, P. I. (2010). Research algorithms identify the model parameters in the adaptive control system extruder. Adaptive automatic control system, Vol. 16 (36), 147-154.

Downloads

Published

2014-06-25

How to Cite

Жученко, О. (2014). Adaptive system of controlling temperature mode of polymer materials extrusion. Eastern-European Journal of Enterprise Technologies, 3(2(69), 57–61. https://doi.org/10.15587/1729-4061.2014.24625

Issue

Vol. 3 No. 2(69) (2014): Information technology. Industry control systems

Section

Industry control systems

License

Copyright (c) 2014 Олексій Жученко

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.