Identification of the influence of micro two-stage refilled friction stir spot welding with variation dwell time on dissimilar brass CuZn30-aluminum AA1100
DOI:
https://doi.org/10.15587/1729-4061.2023.276484Keywords:
Friction Stir Spot Welding, mTS-RFSSW, Brass CuZn30, AA1100, dwell timeAbstract
Welding and joining of brass CuZn30-aluminum AA1100 were obtained using micro two-stage refilled friction stir spot welding (mTS-RFSSW), which was carried out to eliminate the holes formed by the micro friction stir spot welding (mFSSW) process. The mTS-RFSSW process begins with the mFSSW welding process using tools with a pin inner diameter of 2.69 mm, pin outer diameter 1.811 mm and shoulder diameter of 4.954 mm, followed by a second stage process called mTS-RFSSW, which is a hole closing process using a tool with a pinless tool with shoulder diameter 4.954 mm. This study aimed to determine the effect of the second stage of dwell time on the mechanical properties produced in the mTS-RFSSW welding technique using brass CuZn30 and aluminum AA1100 with a thickness of 0.42 mm. In this study, the variable parameter is the second stage dwell time which varies from 3 s, 4 s, 5 s, and 6 s, respectively. An optical microscope that aims to observe the macrostructure shows that an upward hook is formed in each joining process. Based on the scanning electron micrograph, the resulting formation of different intermetallic compounds (IMC) with varying thicknesses occurs in every variation of dwell time. The high dwell time indicates discontinued IMC, which affects the tensile force. The IMC formed at the interface of brass CuZn30 and aluminum AA1100 is dominated by more than 30 % Cu. The highest hardness value is found in the stir zone because the formation of intermetallic compounds influences refined grains. The highest maximum shear force and cross tensile force was obtained 371.35 N and 54.88 N, respectively, in the dwell time of 3 s. The result of fracture properties after the lap shear test shows the presence of small dimples with microcracks that indicate brittle failure
References
- Garg, A., Bhattacharya, A. (2017). Similar and dissimilar joining of AA6061-T6 and copper by single and multi-spot friction stirring. Journal of Materials Processing Technology, 250, 330–344. doi: https://doi.org/10.1016/j.jmatprotec.2017.07.029
- Irawan, Y. S., Choiron, M. A., Suprapto, W. (2021). Tensile strength and thermal cycle analysis of AA6061 friction weld joints with different diameters and various friction times. Eastern-European Journal of Enterprise Technologies, 2 (12 (110)), 15–21. doi: https://doi.org/10.15587/1729-4061.2021.227224
- Darmadi, D. B., Abdillah, F. N., Raharjo, R. (2019). Controlling the pressure force to obtain a better quality of aluminum 6061 friction stir welded joint. Eastern-European Journal of Enterprise Technologies, 3 (1 (99)), 6–10. doi: https://doi.org/10.15587/1729-4061.2019.159286
- Sajed, M. (2016). Parametric study of two-stage refilled friction stir spot welding. Journal of Manufacturing Processes, 24, 307–317. doi: https://doi.org/10.1016/j.jmapro.2016.09.011
- Chen, K., Liu, X., Ni, J. (2017). Keyhole refilled friction stir spot welding of aluminum alloy to advanced high strength steel. Journal of Materials Processing Technology, 249, 452–462. doi: https://doi.org/10.1016/j.jmatprotec.2017.06.039
- Sunar Baskoro, A., Azwar Amat, M., Andre Widiyanto, M. (2019). Effect of Tools Geometry and Dwell Time on Mechanical Properties and Macrograph of Two-Stage Refilled Friction Stir Spot Micro Weld. MATEC Web of Conferences, 269, 02002. doi: https://doi.org/10.1051/matecconf/201926902002
- Esmaeili, A., Sbarufatti, C., Hamouda, A. M. S. (2019). Characteristics of Intermetallic Compounds in Dissimilar Friction Stir Welding: A Review. Metallography, Microstructure, and Analysis, 8 (4), 445–461. doi: https://doi.org/10.1007/s13632-019-00557-w
- Zhou, L., Zhang, R. X., Li, G. H., Zhou, W. L., Huang, Y. X., Song, X. G. (2018). Effect of pin profile on microstructure and mechanical properties of friction stir spot welded Al-Cu dissimilar metals. Journal of Manufacturing Processes, 36, 1–9. doi: https://doi.org/10.1016/j.jmapro.2018.09.017
- Rupajati, P., Clarissa, K. G., Baskoro, A. S., Kiswanto, G., Winarto, W. (2021). Characteristics of Mechanical Properties and Microstructure of Micro Friction Stir Spot Welding of AA1100 and Brass. International Journal of Technology, 12 (6), 1302. doi: https://doi.org/10.14716/ijtech.v12i6.5214
- Shen, Z., Ding, Y., Chen, J., Amirkhiz, B. S., Wen, J. Z., Fu, L., Gerlich, A. P. (2019). Interfacial bonding mechanism in Al/coated steel dissimilar refill friction stir spot welds. Journal of Materials Science & Technology, 35 (6), 1027–1038. doi: https://doi.org/10.1016/j.jmst.2019.01.001
- Li, P., Chen, S., Dong, H., Ji, H., Li, Y., Guo, X. et al. (2020). Interfacial microstructure and mechanical properties of dissimilar aluminum/steel joint fabricated via refilled friction stir spot welding. Journal of Manufacturing Processes, 49, 385–396. doi: https://doi.org/10.1016/j.jmapro.2019.09.047
- Hsieh, M.-J., Lee, R.-T., Chiou, Y.-C. (2017). Friction stir spot fusion welding of low-carbon steel to aluminum alloy. Journal of Materials Processing Technology, 240, 118–125. doi: https://doi.org/10.1016/j.jmatprotec.2016.08.034
- Garg, A., Bhattacharya, A. (2017). Strength and failure analysis of similar and dissimilar friction stir spot welds: Influence of different tools and pin geometries. Materials & Design, 127, 272–286. doi: https://doi.org/10.1016/j.matdes.2017.04.084
- Dong, Z., Song, Q., Ai, X., Lv, Z. (2019). Effect of joining time on intermetallic compound thickness and mechanical properties of refill friction stir spot welded dissimilar Al/Mg alloys. Journal of Manufacturing Processes, 42, 106–112. doi: https://doi.org/10.1016/j.jmapro.2019.04.013
- Shen, Z., Ding, Y., Guo, W., Hou, W., Liu, X., Chen, H. et al. (2021). Refill Friction Stir Spot Welding Al Alloy to Copper via Pure Metallurgical Joining Mechanism. Chinese Journal of Mechanical Engineering, 34 (1). doi: https://doi.org/10.1186/s10033-021-00593-0
- Xue, P., Xiao, B. L., Ma, Z. Y. (2015). Effect of Interfacial Microstructure Evolution on Mechanical Properties and Fracture Behavior of Friction Stir-Welded Al-Cu Joints. Metallurgical and Materials Transactions A, 46 (7), 3091–3103. doi: https://doi.org/10.1007/s11661-015-2909-1
- Zhou, L., Li, G. H., Zhang, R. X., Zhou, W. L., He, W. X., Huang, Y. X., Song, X. G. (2019). Microstructure evolution and mechanical properties of friction stir spot welded dissimilar aluminum-copper joint. Journal of Alloys and Compounds, 775, 372–382. doi: https://doi.org/10.1016/j.jallcom.2018.10.045
- Mubiayi, M. P., Akinlabi, E. T. (2016). Evolving properties of friction stir spot welds between AA1060 and commercially pure copper C11000. Transactions of Nonferrous Metals Society of China, 26 (7), 1852–1862. doi: https://doi.org/10.1016/s1003-6326(16)64296-6
- Zareie Rajani, H. R., Esmaeili, A., Mohammadi, M., Sharbati, M., Givi, M. K. B. (2012). The role of Metal-Matrix Composite development During Friction Stir Welding of Aluminum to Brass in Weld Characteristics. Journal of Materials Engineering and Performance, 21 (11), 2429–2437. doi: https://doi.org/10.1007/s11665-012-0178-3
- Bisadi, H., Tavakoli, A., Tour Sangsaraki, M., Tour Sangsaraki, K. (2013). The influences of rotational and welding speeds on microstructures and mechanical properties of friction stir welded Al5083 and commercially pure copper sheets lap joints. Materials & Design, 43, 80–88. doi: https://doi.org/10.1016/j.matdes.2012.06.029
- Shiraly, M., Shamanian, M., Toroghinejad, M. R., Ahmadi Jazani, M. (2013). Effect of Tool Rotation Rate on Microstructure and Mechanical Behavior of Friction Stir Spot-Welded Al/Cu Composite. Journal of Materials Engineering and Performance, 23 (2), 413–420. doi: https://doi.org/10.1007/s11665-013-0768-8
- Li, G., Zhou, L., Zhou, W., Song, X., Huang, Y. (2019). Influence of dwell time on microstructure evolution and mechanical properties of dissimilar friction stir spot welded aluminum–copper metals. Journal of Materials Research and Technology, 8 (3), 2613–2624. doi: https://doi.org/10.1016/j.jmrt.2019.02.015
![Identification of the influence of micro two-stage refilled friction stir spot welding with variation dwell time on dissimilar brass CuZn30-aluminum AA1100](https://journals.uran.ua/public/journals/3/submission_276484_314650_coverImage_en_US.png)
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Pathya Rupajati, Ario Sunar Baskoro, Latitia Dhayita Pramudito, Laksita Aji Safitri, Mohammad Azwar Amat, Gandjar Kiswanto
![Creative Commons License](http://i.creativecommons.org/l/by/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.