Efficiency evaluation of manufacturing thin porous shells by extrusion

Authors

  • Гарбач Томаш Lublin University of Technology 36 Nadbystrzycka St., Lublin, Poland, 20-618, Poland
  • Володимир Васильович Красінський Lviv Politechnic National University st. S. Bandera, 12, Lviv, Ukraine, 79013, Ukraine https://orcid.org/0000-0001-6374-9340
  • Олег Володимирович Суберляк Lviv Politechnic National University st. S. Bandera, 12, Lviv, Ukraine, 79013, Ukraine https://orcid.org/0000-0002-6046-5972
  • Людмила Дулебова Technical University of Košice Mäsiarska 74, Košice, Slovakia, 040-01, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2015.43746

Keywords:

blowing agent, porous shells, extrusion, cable insulation

Abstract

The paper presents the results of investigating the porous extrusion process of the polyvinyl chloride (PVC) cable shell in the presence of different-nature blowing agents. The aim was to develop a technological process of manufacturing the porous insulating polyvinyl chloride shell of the power cable by extrusion and explore the structure and performance properties of the resulting shell. Based on experimental data, optimal process parameters of manufacturing the porous insulating polyvinyl chloride shell of the power cable by the extrusion were found. The structure and performance properties of the porous shell were examined. It is shown that using endothermic blowing agents in the amount of 0,2-0,8% and exothermic blowing agents in the amount 0.4-0.6% in the extrusion of power cable PVC-shell allows to obtain high-quality product, the cost of which is significantly lower than of the monolithic PVC shell. It is shown that the obtained insulating shell meets national and international requirements.

Author Biographies

Гарбач Томаш, Lublin University of Technology 36 Nadbystrzycka St., Lublin, Poland, 20-618

PhD, lekturer

Department of Polymer Processing

Володимир Васильович Красінський, Lviv Politechnic National University st. S. Bandera, 12, Lviv, Ukraine, 79013

PhD, lekturer

Department of Chemical Technology and Plastics Processing

Олег Володимирович Суберляк, Lviv Politechnic National University st. S. Bandera, 12, Lviv, Ukraine, 79013

Doctor of Science, Head of department, Professor

Department of Chemical Technology and Plastics Processing

Людмила Дулебова, Technical University of Košice Mäsiarska 74, Košice, Slovakia, 040-01

PhD, lekturer

Department of Technologies and Materials

References

  1. Bociaga, E., Palutkiewicz, P. (2012). Wplyw zawartosci poroforu i warunkow wtryskiwania na wybrane wlasciwosci i stan powierzchni wyprasek z polipropylenu. Polimery, 57 (1), 38–48. doi: 10.14314/polimery.2012.038
  2. Garbacz, T. (2013). Structure and properties of cellular injection molded products. Polimery, 58 (4), 295–303. doi: 10.14314/polimery.2013.295
  3. Tejeda, E. H. (2005). Morphology and Mechanical Properties of Foamed Polyethylene-Polypropylene Blends. Journal of Cellular Plastics, 41 (5), 417–435. doi: 10.1177/0021955x05056959
  4. Dulebova, L., Garbacz, T. (2013). Thermal analyzes of polymer composites. Transfer innovacii, 26, 130–134.
  5. Garbacz, T., Krasinskyi, V. (2012). Evaluate the effectiveness of the extrusion process. Conference PRO-TECH-MA. Slovakia, 180–185.
  6. Okamoto, K. T. (2003). Microcellular processing. Carl Hanser Verlag, Munich, Germany.
  7. Sikora, J. W., Samujło, B. (2013). Impact of Feed Opening Width and Position on PVC Extrusion Process Effectiveness. International Polymer Processing, 28 (3), 291–299. doi: 10.3139/217.2729
  8. Zhou, Q. (2005). Exo-endothermic Blowing Agent and its Foaming Behavior. Journal of Cellular Plastics, 41 (3), 225–234. doi: 10.1177/0021955x05053521
  9. Żach, P. (2006). Studies of cellular plastics used for the production of car seats. Plastics and Chemistry, 11–12.
  10. Samujło, B., Sikora, J. W. (2013). The impact of selected granulometric properties of poly(vinyl chloride) on the effectiveness of the extrusion process. Journal of Polymer Engineering, 33 (1), 77–85. doi: 10.1515/polyeng-2012-0100
  11. Sikora, J. W.; Sabu T., Yang, W. (Ed.) (2009). Screw extrusion. Advances in polymer processing. Woodhead Publishing Limited. Oxford-Cambridge-New Delhi, United Kingdom, 106–142.

Downloads

Published

2015-06-17

How to Cite

Томаш, Г., Красінський, В. В., Суберляк, О. В., & Дулебова, Л. (2015). Efficiency evaluation of manufacturing thin porous shells by extrusion. Eastern-European Journal of Enterprise Technologies, 3(6(75), 10–15. https://doi.org/10.15587/1729-4061.2015.43746

Issue

Vol. 3 No. 6(75) (2015): Technology organic and inorganic substances. Ecology

Section

Technology organic and inorganic substances

License

Copyright (c) 2015 Гарбач Томаш, Володимир Васильович Красінський, Олег Володимирович Суберляк, Людмила Дулебова

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.