Machine guides restoration by using a polymeric material
DOI:
https://doi.org/10.31498/2225-6733.30.2015.52697Keywords:
lathe, rest, guide, the coefficient of friction, polymeric materialAbstract
The restoration of slide rest guides of the automatic lathe PUB 130 was made by using a polymeric material in the laboratory, and the measurements of the rest displacement strength were made on a specially created experimental stand with the ADC and the PC and subsequent determination of the coefficient of friction. The performed experiments revealed that in the speed range of saddle feed from 0,0228 to 0,075 m/s, the coefficient of friction is within 0,047-0,055. At the same time, the transition to the low-feed (0,0005-0,0022 m/s) results in to marked increase of the friction coefficient and the rest hopping movement. However, this phenomenon is likely due to the fact that elastic tie in the form of steel beam with tensometers was put into the feeder of the rest. This explanation let us hope that, with rigid connection of the drive and the rest such a phenomenon will not take place and the value of friction will not differ substantially from the friction obtained at high speeds. The obtained results make it possible to consider the use of a polymer material to be the optimal way to restore worn-out machinesReferences
Ищенко Е.А. Современные способы и материалы для восстановления пар трения / Е.А. Ищенко, В.П. Гришко // Захист металургійних машин від поломок : Зб. наук. пр. / ДВНЗ «ПДТУ». – Маріуполь, 2013. – Вип. 15. – С. 173-177.
Савчук П.П. Эпоксидные композиции в узлах трения скольжения / П.П. Савчук // Проблемы трения и износа. – 2011. – №56. – С. 243-251.
Близнец М.М. Особенности изнашивания эпоксидных полимеров / М.М. Близнец, Н.П. Богданович, П.Д. Стухляк // Трение и износ. – 1988. – Т. 9 – №9. – С. 549-552.
Мышкин Н.К. Трибология полимеров: адгезия, трение, изнашивание и фрикционный перенос / Н.К. Мышкин, М.И. Петроковец, А.В. Ковалев // Трение и износ. – 2006. – Т. 27 – №4. – С. 429-443.
Квашин Б.Н. Восстановление направляющих скольжения металлорежущих станков / Б.Н. Квашин, Ю.Д. Симонова, Ю.С. Ткаченко, В.Н. Гадалов // Известия Юго-Западного государственного университета. – 2013 – №5 (50). – С. 139-141.
Леванцевич М.А. Механизмы изнашивания направляющих скольжения металлообрабатывающего оборудования / М.А. Леванцевич, А.Т. Схиртладзе // Ремонт, восстановление, модернизация. – 2006 – №5. – С. 41-46.
Downloads
How to Cite
Issue
Section
License
The journal «Reporter of the Priazovskyi State Technical University. Section: Technical sciences» is published under the CC BY license (Attribution License).
This license allows for the distribution, editing, modification, and use of the work as a basis for derivative works, even for commercial purposes, provided that proper attribution is given. It is the most flexible of all available licenses and is recommended for maximum dissemination and use of non-restricted materials.
Authors who publish in this journal agree to the following terms:
1. Authors retain the copyright of their work and grant the journal the right of first publication under the terms of the Creative Commons Attribution License (CC BY). This license allows others to freely distribute the published work, provided that proper attribution is given to the original authors and the first publication of the work in this journal is acknowledged.
2. Authors are allowed to enter into separate, additional agreements for non-exclusive distribution of the work in the same form as published in this journal (e.g., depositing it in an institutional repository or including it in a monograph), provided that a reference to the first publication in this journal is maintained.
