Substantiation of adequacy of loading conditions at bench and field tests of construction machines

Authors

DOI:

https://doi.org/10.15587/1729-4061.2018.130996

Keywords:

accelerated bench tests, random loads, hypothesis of spectral summation, chassis

Abstract

Loading conditions for construction machines at bench tests were substantiated. Adequacy of loading conditions at bench tests and of the loads acting on construction machines in actual operating conditions was substantiated.

When releasing each machine from the manufacturer's enterprise, it is subjected to tests. Most often, these tests are carried out on specially equipped test sites. Their use requires large financial and time inputs: delivery of the machine, washing and cleaning from dirt after testing, fee to operators. More accurate results are obtained with bench tests at operational loading conditions. Shortening of such test duration is achieved by reducing the work interruptions and improving the shift planning. Except tests for permanent loading, it is expedient to test construction machines and their work elements for impact loads.

This study has established necessity of adherence to the following test conditions: the assembly under study should not approach resonance; the effect of frequencies of the repeated variable loading on the fatigue destruction process should be insignificant. Compliance with these conditions makes it possible to use the mathematical apparatus given in the paper for calculation of endurance at various loading parameters and simulation of various machine operation conditions.

The procedure developed in this work makes it possible to save not only time and money. In manufacture, it shortens design of construction machines and ensures identification of assemblies that reduce reliability or require longer life. This results in a smaller metal consumption or improved quality of the machine. In the mass production, it enables conduction of periodic accelerated qualitative tests of the machine, determination of modernization efficiency, creation of new designs of the bench for testing construction machines. In the process of machine operation, it helps to reduce loads on the machine structures and improve reliability and durability.

Author Biographies

Leonid Pelevin, Kyiv National University of Construction and Architecture Povitroflotsky ave., 31, Kyiv, Ukraine, 03037

PhD, Professor

Department of Construction Machinery

Anatoliy Fomin, Kyiv National University of Construction and Architecture Povitroflotsky ave., 31, Kyiv, Ukraine, 03037

PhD, Professor

Department of Construction Machinery

Ievgenii Gorbatyuk, Kyiv National University of Construction and Architecture Povitroflotsky ave., 31, Kyiv, Ukraine, 03037

PhD, Associate Professor

Department of Construction Machinery

Grigory Machishin, Kyiv National University of Construction and Architecture Povitroflotsky ave., 31, Kyiv, Ukraine, 03037

PhD, Associate Professor

Department of Construction Machinery

References

  1. Zagarin, D. A., Zarayskiy, A. I. (2011). Poligon tests – a criterion for assessing the reliability of domestic vehicles. Journal of Automotive Engineers, 3 (68), 10–13. Available at: http://www.aae-press.ru/f/68/4.pdf
  2. Yoshida, K., Masuda, T., Kawanago, K., Hiraide, S., Kimura, M., Kobayashi, J. (2012). Introduction of Construction Machine EMC Test Facility. Komatsu technical report, 58 (165), 1–5. Available at: http://www.komatsu.com/CompanyInfo/profile/report/pdf/165-E05.pdf
  3. Bondarev, O., Gorobets, V., Grushak, I. (2008). Determination of the service life of bearing structures of the motor-wagon rolling stock with the use of a method for comparing their dynamic load. Visn. Dnipropetrovsk. nats. Un-th. iron trans them acad. V. Lazaryan, 24, 18–24. Available at: http://eadnurt.diit.edu.ua/jspui/handle/123456789/391
  4. Gorobets, V., Bondarev, O., Skoblenko, V. (2010). Analysis of operational structure of bearing structures of rolling stock in tasks of prolongation of its exploitation. Visn. Dnipropetrovsk. nats. Un-th iron trans them acad. V. Lazaryan, 35, 10–16.
  5. Moskvichev, V., Doronin, S. (2008). New Approaches to Design Calculations in Mining Engineering. Mining Information Analytical Bulletin, 63–70.
  6. Nagata, T., Shichino, H., Tamura, Y., Kawai, H., Ohta, Y., Komori, M. (2013). Development of optimal tooth flank in spiral bevel gears by contact analysis and measurement. Technical Paper. Komatsu technical report, 59 (166), 1–8. Available at: http://www.komatsu.com/CompanyInfo/profile/report/pdf/166-E01.pdf
  7. Makarov, A. (2011). Development of fatigue cracks in excavator metal structures. Herald of IrSTU, 11 (58), 105–109. Available at: https://cyberleninka.ru/article/n/razvitie-ustalostnyh-treschin-v-metallokonstruktsiyah-ekskavatorov
  8. Kotiev, G., Zorin, D. (2008). Forecasting of Durability of the Transport machines parts. The world of transport, 1, 4–9.
  9. Mezyk A., Switoski E., Kciuk S., Klein W. (2011). Modeling and Investigation of Dynamic Parameters of Tracked Vehicles. Mechanics and Mechanical Engineering, 15 (4), 115–130. Available at: http://kdm.p.lodz.pl/articles/2011/15_4_11.pdf
  10. Janarthanan, B., Padmanabhan, C., Sujatha, C. (2012). Longitudinal dynamics of a tracked vehicle: Simulation and experiment. Journal of Terramechanics, 49 (2), 63–72. doi: 10.1016/j.jterra.2011.11.001
  11. Zaitsev, V., Kurtz, D. (2012). The basic model of the dynamics of the spatial motion of a caterpillar on the terrain with a complex relief and an arbitrary form of unevenness. Proceedings of 15 Vseross. scientific and practical conf. NGO Special Materials, Vol. 3: Armored vehicles and weapons. Saint Petersburg, 174–180.
  12. Usov, O., Beloutov, G. (2013). Mathematical model of the suspension system for calculating the transient modes of operation of the engine-transmission units of military caterpillar vehicles. Actual problems of protection and security. Proceedings of the 15th All-Russian Scientific and Practical Conference, Vol. 3: Armored vehicles and weapons. Saint Petersburg: NGO Special Materials, 172–180.
  13. Kuroki, M., Miyake, M., Hirama, H., Morita, M., Ozawa, E. (2015). Life Improvement of Floating Seal. Technical Paper. Komatsu technical report, 61 (168), 1–6. Available at: http://www.komatsu.com/CompanyInfo/profile/report/pdf/168-E02.pdf
  14. Grečenko, A. (2007). Re-examined principles of thrust generation by a track on soft ground. Journal of Terramechanics, 44 (1), 123–131. doi: 10.1016/j.jterra.2006.04.002
  15. Shinoda, T., Nagata, Y. (2015). Trend of 3D Measurement Technology and Its Application. Technical Paper. Komatsu technical report, 61 (168), 1–5. Available at: http://www.komatsu.com/CompanyInfo/profile/report/pdf/168-E03.pdf
  16. Berezin, I., Richter, E. (2008). Thermal calculation and prediction of the limiting state of elastomeric structures. Materials of the international conference "Modern state and innovations in the transport complex". Perm: Publishing house of PSTU, 94–100.
  17. Rykov, S., Bekirova, R., Koval, V. (2010). Modeling of a random microprofile of highways. Systems. Methods. Technologies, 4 (8), 33–37.
  18. Haydamak, A. (2011). Tests on wear parts of roller bearings of heavy operating modes. Problems of Tribology, 1, 19–24.
  19. Belyaev, V. (2013). Tests of cars. Chelyabinsk: Publishing Center of SUSU, 293.
  20. Shemyakin, S., Leshchinsky, A. (2014). Calculation of earth-moving machines. Khabarovsk: Publishing house of the Pacific. state. un-ta, 55.
  21. Khmara, L. et. al.; Khmara, L., Kravеts', S. (Eds.) (2010). Machines for earthmoving. Rivne – Dnipropetrovsk – Kharkiv, 557.
  22. Livinsky, O., Yesipenko, A., Khorok, O., Pelevin, L., Smirnov, V., Volyunyuk, V. (2013). Construction machinery. Kyiv: Kyiv National University of Construction and Architecture, Ukrainian Academy of Sciences, "MP LESYA", 614.
  23. Vlasov, V. (1972). On the calculation of working equipment of rotary excavators for endurance. Horn. builds. anddor.machines, 14, 17–21.
  24. Sarafanov, G., Perevezentsev, V. (2007). Regularities of deformation grinding of the structure of metals and alloys. Educational-methodical material on the advanced training program "Modern technologies for creating new materials of electronics and optoelectronics for information and telecommunication systems". Nizhny Novgorod, 96.
  25. Sannikov, A., Kutsubina, N. (2008). Theory and design of machinery and equipment industry. Methods of designing, forecasting, optimization of machines and equipment of the forest complex. Ekaterinburg: the Urals. state. forestry. un-t, 121.
  26. Vazhinsky, S., Shcherbak, T. (2016). Methodology and Organization of Scientific Research. Sumy: Sumy State University named after A. S. Makarenko, 260.
  27. Vanin, V. A., Odnol'ko, V. G., Pestrecov, S. I., Fidarov, V. H., Kolodin, A. N. (2009). Scientific research in mechanical engineering. Tambov: Publishing house of Tambov. state tech un-that, 232.
  28. Cherkasov, V. et. al.; Kaytukov, B. A., Skel', V. I. (Eds.) (2015). Reliability of machines and mechanisms. Moscow: NIU MSSU, 272.

Downloads

Published

2018-05-14

How to Cite

Pelevin, L., Fomin, A., Gorbatyuk, I., & Machishin, G. (2018). Substantiation of adequacy of loading conditions at bench and field tests of construction machines. Eastern-European Journal of Enterprise Technologies, 3(7 (93), 41–52. https://doi.org/10.15587/1729-4061.2018.130996

Issue

Vol. 3 No. 7 (93) (2018): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2018 Leonid Pelevin, Anatoliy Fomin, Ievgenii Gorbatyuk, Grigory Machishin

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.