Indentifying the conditions for the occurrence of static self-balancing for an assymetric rotor on two isotropic elastic supports
DOI:
https://doi.org/10.15587/1729-4061.2020.200428Keywords:
rotor, isotropic support, automatic balancer, stationary motion, motion stability, steady motion equation.Abstract
This paper reports the established conditions for static self-balancing for the case of an asymmetric rotor on two isotropic elastic supports, balanced by a passive automatic balancer of any type. In general, the plane of static imbalance does not coincide with the plane of an automatic balancer.
The energy method has been used under the assumption that the mass of an automatic balancer's loads is much smaller than the mass of the rotor.
It has been established that the static balancing of the rotor by an automatic balancer of any type is possible in the following cases:
‒ a long rotor when the rotor rotates at speeds between the first and second and above the third characteristic velocities;
‒ a spherical rotor when the rotor rotates at speeds between the first and second characteristic velocities;
‒ a short rotor at speeds exceeding a certain characteristic velocity provided that the automatic balancer is close to the center of the rotor mass.
The rotor asymmetry increases the number of resonant speeds but the number of regions where the self-balancing is occurred does not change.
The imbalance of the rotor and its location do not affect the characteristic rotation speeds of the rotor. An automatic balancer in the range of rotor rotation velocities that ensure the self-balancing tends to maximally reduce the deviation of its center from the rotor rotation axis. When the rotation velocity of a long or spherical rotor approaches the second characteristic speed, the automatic balancer's capacity ceases to provide for the complete elimination of the automatic balancer's axis deviation from the rotor's rotation axis.
The result obtained summarizes the findings derived earlier when using the empirical criterion for the occurrence of self-balancing. The energy method, in contrast to the empirical method, has made it possible to estimate the residual deviation of the rotor's longitudinal axis from the rotation axis. That allows the estimation of the reserve or the calculation of the automatic balancer's balancing capacity.
The type of automatic balancers is not taken into consideration in such studies. Therefore, the results obtained are suitable for automatic balancers of any type, and the method itself is suitable for constructing a general theory of passive self-balancing (applicable for automatic balancers of any type).
References
- Thearle, E. L. (1950). Automatic dynamic balancers (Part 2 – Ring, pendulum, ball balancers). Machine Design, 22 (10), 103–106.
- Filimonikhin, G., Olijnichenko, L. (2015). Investigation of the possibility of balancing aerodynamic imbalance of the impeller of the axial fan by correction of masses. Eastern-European Journal of Enterprise Technologies, 5 (7 (77)), 30–35. doi: https://doi.org/10.15587/1729-4061.2015.51195
- Chen, H.-W., Zhang, Q. (2017). Design of horizontal axis washing machine with ball balancer and MR dampers. International Journal of Precision Engineering and Manufacturing, 18 (12), 1783–1793. doi: https://doi.org/10.1007/s12541-017-0207-0
- Royzman, V., Drach, I., Tkachuk, V., Pilkauskas, K., Čižauskas, G., Šulginas, A. (2019). Operation of Passive Fluid Self-Balancing Device at Resonance Transition Regime. Mechanics, 24 (6), 805–810. doi: https://doi.org/10.5755/j01.mech.24.6.22469
- Chen, H.-W., Zhang, Q.-J. (2016). Dynamic Analysis and Design of a Balancer for a Three-Column Centrifuge. Shock and Vibration, 2016, 1–13. doi: https://doi.org/10.1155/2016/7957821
- Chao, P. C.-P., Sung, C.-K., Wu, S.-T., Huang, J.-S. (2006). Nonplanar modeling and experimental validation of a spindle–disk system equipped with an automatic balancer system in optical disk drives. Microsystem Technologies, 13 (8-10), 1227–1239. doi: https://doi.org/10.1007/s00542-006-0337-2
- Rodrigues, D. J., Champneys, A. R., Friswell, M. I., Wilson, R. E. (2011). Experimental investigation of a single-plane automatic balancing mechanism for a rigid rotor. Journal of Sound and Vibration, 330 (3), 385–403. doi: https://doi.org/10.1016/j.jsv.2010.08.020
- Sperling, L., Ryzhik, B., Duckstein, H. (2004). Single-Plain Auto-Balancing of Rigid Rotors. Technische Mechanik, 24 (1), 1–24.
- Filimonikhin, G., Filimonikhina, I., Dumenko, K., Lichuk, M. (2016). Empirical criterion for the occurrence of auto-balancing and its application for axisymmetric rotor with a fixed point and isotropic elastic support. Eastern-European Journal of Enterprise Technologies, 5 (7 (83)), 11–18. doi: https://doi.org/10.15587/1729-4061.2016.79970
- Gorbenko, A. N., Shmelev, S. Kh. (2018). Necessary Self-Balancing Robustness Conditions for a Two-Bearing Rotor Taking Unbalance Mass into Account. Herald of the Bauman Moscow State Technical University. Series Mechanical Engineering, 5 (122), 36–50. doi: https://doi.org/10.18698/0236-3941-2018-5-36-50
- Filimonikhin, G., Filimonikhina, I., Ienina, I., Rahulin, S. (2019). A procedure of studying stationary motions of a rotor with attached bodies (auto-balancer) using a flat model as an example. Eastern-European Journal of Enterprise Technologies, 3 (7 (99)), 43–52. doi: https://doi.org/10.15587/1729-4061.2019.169181
- Filimonikhin, G., Filimonikhina, I., Pirogov, V., Rahulin, S., Sadovyi, M., Strautmanis, G. et. al. (2020). Establishing conditions for the occurrence of dynamic auto-balancing in a rotor on two elastic-viscous supports. Eastern-European Journal of Enterprise Technologies, 1 (7 (103)), 50–57. doi: https://doi.org/10.15587/1729-4061.2020.192598
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2020 Irina Filimonikhina, Viktor Deikun, Iryna Ienina, Mareks Mezitis, Vladimir Pirogov, Guntis Strautmanis, Sergij Yakimenko
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.
