Research of details surface micro-relief with the superficial work-hardened layer after an abrasive wear

Authors

  • S. S. Samotugin ДВНЗ «Приазовський державний технічний університет», м. Маріуполь, Ukraine
  • V. O. Haharin ДВНЗ «Приазовський державний технічний університет», м. Маріуполь, Ukraine

DOI:

https://doi.org/10.31498/2225-6733.28.2014.33745

Keywords:

plasma work-hardening, discrete treatment, micro-relief, wear resistance

Abstract

The results of researches of surface roughness changes are presented after the plasma work-hardening and subsequent wear. Influence of placing of the work-hardened zones was checked up on surfaces in relation to direction of the mutual skidding of details on the change of roughness after a wear

Author Biographies

S. S. Samotugin, ДВНЗ «Приазовський державний технічний університет», м. Маріуполь

Доктор технічних наук, професор

V. O. Haharin, ДВНЗ «Приазовський державний технічний університет», м. Маріуполь

Асистент

References

Самотугин С.С. Плазменное упрочнение инструментальных материалов / С.С. Самотугин, Л.К. Лещинский. – Донецк: Новый мир, 2002. – 338 с.

Гаркунов Д.Н. Триботехника (конструирование, изготовление и эксплуатация машин): Учебник. - 5-е изд., перераб. и доп. / Д.Н. Гаркунов. – М.: «Издательство МСХА», 2002. – 632 c, ил. 250.

Основы трибологии (трение, износ, смазка): учебник для технических вузов. 2-е изд. перераб. и доп. / А.В. Чичинадзе [и др.]; Под общ. ред. А.В. Чичинадзе. – М.: Машиностроение, 2001. – 664с., ил.

Оценка влияния градиентной плазменной модификации на напряженное состояние поверхности стальных изделий / С.С. Самотугин [и др.] // Захист металургійних машин від поломок: Зб. наук. пр. – Маріуполь: ДВНЗ «ПДТУ», 2012. – Вип.13. – С. 121-124.

Downloads

How to Cite

Samotugin, S. S., & Haharin, V. O. (2014). Research of details surface micro-relief with the superficial work-hardened layer after an abrasive wear. Reporter of the Priazovskyi State Technical University. Section: Technical Sciences, (28), 152–157. https://doi.org/10.31498/2225-6733.28.2014.33745

Issue

No. 28 (2014): Reporter of the Priazovskyi State Technical University. Section: Technical sciences

Section

Mechanical engineering and metal working

License

The journal «Reporter of the Priazovskyi State Technical University. Section: Technical sciences» is published under the CC BY license (Attribution License).

This license allows for the distribution, editing, modification, and use of the work as a basis for derivative works, even for commercial purposes, provided that proper attribution is given. It is the most flexible of all available licenses and is recommended for maximum dissemination and use of non-restricted materials.

Authors who publish in this journal agree to the following terms:

1. Authors retain the copyright of their work and grant the journal the right of first publication under the terms of the Creative Commons Attribution License (CC BY). This license allows others to freely distribute the published work, provided that proper attribution is given to the original authors and the first publication of the work in this journal is acknowledged.

2. Authors are allowed to enter into separate, additional agreements for non-exclusive distribution of the work in the same form as published in this journal (e.g., depositing it in an institutional repository or including it in a monograph), provided that a reference to the first publication in this journal is maintained.